Verine Midas HE Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 39

Verine Midas HE Скачать руководство пользователя страница 32

About your Verine Midas HE

The Verine Midas HE range of coal & pebble fuel-bed gas fires incorporates a
unique and highly developed fuel bed which gives the realism of a loose coal or
pebble layout combined with realistic flames and glow. The use of durable
ceramic material in the construction of the fuel-bed components ensures long and
trouble free operation.

When first using the new fire a slight smell may be noticed. This is due to starch
used in the manufacture of the soft ceramic coal or pebble form, it is non-toxic and
will soon disappear.

Please take the time to fully read these instructions as you will then be able to
obtain the most effective and safe operation of your fire.

IMPORTANT SAFETY INFORMATION

WARNING

This appliance has a naked flame and as with all heating appliances a
fireguard should be used for the protection of children, the elderly and
infirm. Fireguards should conform to B.S. 8423 : 2002 (Fireguards for use
with gas heating appliances).

It is important that this appliance is serviced at least once a year by a GAS SAFE
registered gas installer and that during the service the fire is removed from the fire
opening and the chimney or flue visually checked for fallen debris or blockages
which must be removed. The chimney should also be checked to ensure
clearance of flue products. These are conditions of the manufacturers
guarantee. After installation or during servicing a spillage test must always
be carried out.

THE FIRE MUST NOT BE OPERATED WITH THE GLASS CRACKED, BROKEN
OR REMOVED. Any debris or deposits should be removed from the fuel-bed from
time to time. This may be carried out by referring to the cleaning section as
described later in this book.

Only the correct coal or pebble fuel-bed must be used and only complete and
genuine replacement fuel-beds must be sourced from BFM Europe Ltd.
The appliance must only be used with the coal or pebble fuel-bed supplied and
must not be used with other coals or pebble fuel-beds.

Always keep furniture and combustible materials well clear of the fire and never
dry clothing or items either on or near to the fire. Never use aerosols or
flammable cleaning products near to the fire when it is in use.

32

«
...
30
31
32
33
34
...
»

Содержание Midas HE








































Отзывы:

Нет отзывов