VERDER TZF 12/75/700 Скачать руководство пользователя | Manualshive

Страница: 20 / 80

background image

3.0 3508 Controller

3.7.3

Units

Press page

until "Units" is displayed. Press up

or down

to select:

C

Celsius

F

Fahrenheit

K

Kelvin

3.7.4

Language

The text on the 3508 Controller can be shown in different languages, this can only be set
at the factory and therefore must be specified at the time of placing an order.

3.8

Programming

3.8.1

Programming Notes

Programs can be created in Level 1 or Level 2 of the 3508 Controller.

For the P10 and P25, new programs can be created while the current program is
operating.

To avoid unwanted heating at the end of a program, set the controller setpoint
temperature to zero before operating a program.

All new unused programs show only 1 segment of type 'End'.

The minimum number of segments for a program is 2. The second being an 'End' type.

Ramp-to-setpoint control. To achieve this, create a two segment program. Set the first
segment type as 'Rate' or 'Time'. Set the second segment type 'End' type' Dwell'.

For the P10 and P25, programs can be linked together using a 'Call' segment. However,
a lower number program can not be called and a program can not be ended with a call
segment.

A program can be ended in four ways:

1. With 'End' segment set to S.OP the power to the elements is turned down to 0%,

no matter what the 'Setpoint' temperature is.

2. With 'End' segment set to 'Reset' and the 'Setpoint' temperature turned down to

zero, power to the elements will be 0%. To do this set the 'Setpoint' temperature
to the minimum possible. For type B thermocouples this will be below zero.

3. With the 'End' segment set to 'Reset'. The controller will try to reach and maintain

the 'Setpoint' temperature in place before the program started.

4. With the 'End' segment set to 'Dwell'. The controller will dwell at the 'PSP' of the

last segment ("RUN" indicator flashes), until it is reset.

To reduce the number of segments in a program, change the last required segment to
an 'End' type.

You will be asked to press

to cancel or

for OK.

To cancel all segments in a program, change the first segment to an 'End' type.

20

«
...
18
19
20
21
22
...
»

Содержание TZF 12/75/700

















































































Отзывы:

Нет отзывов

Похожие инструкции для TZF 12/75/700

Бренд: Amana Страницы: 70

Бренд: Yumpu Страницы: 24

Бренд: Empire Heating Systems Страницы: 30

Бренд: Whirlpool Страницы: 8

Бренд: Whirlpool Страницы: 16

Бренд: Whirlpool Страницы: 28

CARBOLITE GERO HRF 7/22

Бренд: VERDER Страницы: 30

Бренд: Lennox Страницы: 52

Бренд: Yumpu Страницы: 24

Бренд: Barnstead|Thermolyne Страницы: 36

Бренд: York Страницы: 24

Бренд: ICP Страницы: 20

Бренд: Rapid Страницы: 58

Бренд: York International Страницы: 12

Бренд: Yamato Страницы: 48

Бренд: Yamato Страницы: 65

Бренд: Temp-O-Matic Страницы: 28

Бренд: Empire Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды