VERDER TZF 12/75/700 Скачать руководство пользователя

Страница: 7 / 80

1.0

Symbols and Warnings

1.1

Switches and Lights

Instrument switch: when the instrument switch is operated the
temperature control circuit is energised.

Heat light: the adjacent light glows or flashes to indicate that power
is being supplied to the elements.

Heat switch: the switch disconnects power to the heating elements;
unless this switch is OFF there is a danger of electric shock when
inserting objects into the product.

1.2

General Warnings

DANGER – Electric shock. Read any warning printed next to this
symbol.

WARNING: Risk of fatal injury.

DANGER – Hot surface. Read any warning printed next to this
symbol.

WARNING: All surfaces of a product may be hot.

DANGER – Read any warning printed next to this symbol.

1.0 Symbols and Warnings

Содержание TZF 12/75/700

















































































Результаты поиска

Содержание TZF 12/75/700

Отзывы:

Похожие инструкции для TZF 12/75/700

Бренды по названию

Популярные бренды

VERDER TZF 12/75/700, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание TZF 12/75/700

Отзывы:

Похожие инструкции для TZF 12/75/700

Бренды по названию

Популярные бренды