Verco Oblique Adapt Скачать руководство пользователя страница 16

Страница: 16 / 19

Error Code in the display of the handset (optional)

Display

Source

Remedying

HOT The

control

unit

monitors

the duty cycle (time-
controlled) and its max.
temperature. A value has
been exceeded.

Wait until the "HOT" goes out, then the
table is working properly again.

E00

M1 – Internal fault

Unplug! and contact the customer service

E01

M2 – Internal fault

E02

M3 – Internal fault

E12

M1 – Defect

Unplug!
Correct the external short circuit and / or
verify the cable to the drives
Take the control unit back in operation.

E13 M2

–

Defect

E14

M3 – Defect

E24

M1 – Overcurrent

Collision? -> resolve if necessary

max. Load exceeded -> remove the load
from the table.

If the problem still exists after that, please
contact customer service.

E25

M2 – Overcurrent

E26

M3 – Overcurrent

E36

M1 – Not connected

Motor not connected
Check cable / connector to the drive
Reset the table.

E37 M2

–

Not

connected

E38 M3

–

Not

connected

E48 Overcurrent

drive 1

Collision? -> resolve if necessary

max. Load exceeded -> remove the load
from the table.

E49 Overcurrent

drive 2

E55

Drive 1 – Synchronization
is lost

Motor position to different, if necessary
reduce the load on the table.

Reset the table.

E56

Drive 2 – Synchronization
is lost

E60

Collision identified

Optional ISP function.
Remove source.

E61

Drive replaced

The Connection to the drive is interrupted
or a new drive is connected.
Reset the table.

Содержание Oblique Adapt




















Результаты поиска

Содержание Oblique Adapt

Отзывы:

Бренды по названию

Популярные бренды

Verco Oblique Adapt, Руководство по сборке и эксплуатации

Результаты поиска

Содержание Oblique Adapt

Отзывы:

Бренды по названию

Популярные бренды