background image

Verasys® 32 Point 24 VAC Application Controller Installation Instructions

1

Application

The Verasys® Application Controller is part of the SMART Equipment Controller family. The Verasys Application 
Controllers run pre-engineered applications and provide the inputs and outputs required to monitor and control a 
wide variety of HVAC equipment.

Verasys Application Controllers operate on an RS-485 BACnet® (MS/TP) Bus as BACnet Advanced Application 
Controllers (B-AACs) and integrate into Johnson Controls® and third-party BACnet systems.

Verasys Application Controllers have an integral real-time clock. The clock functionality monitors and controls 
schedules, calendars, trends, and operate for extended periods of time as stand-alone controllers when offline from 
the system network. 

Verasys 32 Point 24VAC Application Controller Features

The Verasys Application Controllers are used in a Verasys system. The Verasys 32 Point 24 VAC Application 
Controller comes without an application, but you can load custom built applications into this controller. Depending 
on your market, you can access an application library in certain markets. Contact your local Verasys 
representative. The Verasys 32 Point 240VAC Application Controller has the following features:

Input/Output (I/O) quantities and characteristics of the Verasys Application Controller

Real-time clock with local display

Built-in BACnet schedule objects and calendars

Mobile Access Portal (MAP) Gateway compatibility for configuration through smart mobile devices and remote
connectivity

Verasys Smart Building Hub (SBH) compatible through the BACnet MSTP system bus connection

Dedicated Sensor bus for Johnson Controls smart end-devices

Dedicated Modbus port for third-party end-device integration with Modbus

Multi-protocol support for BMS integration BACnet MSTP, N2 and Modbus RTU, through on-board display

IMPORTANT:

Use this Verasys Application Controller only as an operating control. Where failure or 

malfunction of the Verasys Application Controller could lead to personal injury or property damage to the 
controlled equipment or other property, additional precautions must be designed into the control system. 
Incorporate and maintain other devices, such as supervisory or alarm systems or safety or limit controls, 
intended to warn of or protect against failure or malfunction of the Verasys Application Controller.

IMPORTANT:  

Utiliser ce Verasys Application Controller uniquement en tant que dispositif de contrôle de 

fonctionnement. Lorsqu'une défaillance ou un dysfonctionnement du controller risque de provoquer des 
blessures ou d'endommager l'équipement contrôlé ou un autre équipement, la conception du système de 
contrôle doit intégrer des dispositifs de protection supplémentaires. Veiller dans ce cas à intégrer de façon 
permanente d'autres dispositifs, tels que des systèmes de supervision ou d'alarme, ou des dispositifs de 
sécurité ou de limitation, ayant une fonction d'avertissement ou de protection en cas de défaillance ou de 
dysfonctionnement du Verasys Application Controller.

Verasys® 32 Point 24 VAC Application Controller

Installation Instructions

LC-VAC300x-0

Part No. 24-10143-01515, Rev A

Issued May 2018

  24-10143-01515, Rev —   

*2410143015

Содержание LC-VAC300 0 Series





























Отзывы: