background image

9

10

PROCEDURE

STEP 2

Press the button on the receiver for a short time.

The LED comes on and stays on.

STEP 3

Make a transmission with the transmitter to be saved 

(see transmitter manual, paragraph entitled "transmitter

programming").

The LED on the receiver flashes 3 times to signal

that it has been received.

MAKE A TRANSMISSION

WITH THE TRANSMITTER

THE LED FLASHES 3 TIMES

MULTIFUNCTION TRANSMITTER

(see models and codes

on previous page)

GENERIC TRANSMITTER

(see models and codes

on previous page)

WHICH TRANSMITTER DO YOU

WANT TO PROGRAMME?

STEP 1a

Position DIPs 1, 2 and 3 to

ON-ON-ON

DIP 1, 2, 3 =

ON ON ON

STEP 1b

Positions DIPs 1, 2 and 3

according to the function you want to 

associate with the remote control key.

See table 5.1 on the previous page.

SHORT

PRESSURE

SHORT

PRESSURE

STEP 4

The control unit listens for 30 seconds in case you want to add 

other transmitters.

To immediately exit the procedure give a short pressure

on the button on the receiver. 

The LED turns off

This procedure lets you programme multifunctional or generic compatible transmitters.

WHICH REMOTE CONTROL DO YOU WANT TO ASSOCIATE WITH THE CONTROL UNIT?

MULTIFUNCTIONAL TRANSMITTERS - 

MODELS AND CODES

UP / STOP / DOWN / STOP

DIP :

ON ON OFF

UP

DIP :

OFF ON ON

DOWN

DIP :

ON OFF ON

POSITION OF DIP IN "STEP 1b"

OF THE PROCEDURE

TABLE 5.1A

KEY FUNCTIONS OF THE GENERIC TRANSMITTER

KEY

FUNCTION

With multifunctional transmitters the transmitter control modes depend on the model used.

Refer to the transmitter manual, to the paragraph entitled "commands sent by the transmitter",

bearing in mind that it is a "motor” device.

GENERIC TRANSMITTERS - 

MODELS AND CODES

With generic transmitters, the transmitter's control modes depend on the function associated with the key

during the association procedure (see the following page).

The available function for the key are:

STOP

DIP :

OFF OFF ON

5 - RADIO PROGRAMMING

CODE:

BLACK VELA TONDO 30

CODE:

VELA TX 220V-3V

CODE:

WHITE VELA TONDO 6,

BLACK VELA TONDO 6

Содержание VELA-RX

















Отзывы: