background image

5

CONNECTION SCHEME

TERMINALS CONNECTIONS

–1

NEGATIVE POWER SUPPLY OV GND

+2

POSITIVE POWER 13.8V

c3

SOUNDER CONTROL

4

ON/OFF - ALARM SYSTEM STATUS NOTICE

5

FLASH RESET / BLOCK SPEAKER INPUT

6

ANOMALY OUTPUT. OPEN COLLECTOR 
0V = NO ANOMALY

7

N.C. SELF-PROTECTION AND ANTI-FOAM

8

N.C. SELF-PROTECTION AND ANTI-FOAM

A

RED RGB LED INPUT

B

GREEN RGB LED INPUT

C

BLUE RGB LED INPUT

D

WHITE RGB LED INPUT

ANOMALY OUTPUT

 

The sounder is managed by a microcontroller able to check battery recharge, battery status and the speaker; in 

case of anomaly, open collector terminal (6) opens.

Every 22 hours, the microcontroller automatically performs the battery test, notified by LD4 fast flash and other tests

every 10 sec. In case of anomaly, LD4 LED blinks according to the table below.

If the sounder is 

correctly powered

, the anomaly output (terminal no. 6) 

usually stays at 0V

 (current max 50mA). In

case a test performed 

is not passed

, the anomaly output 

disconnects from ground and becomes free

Notification of last anomaly, indicated by LED LD4 is reset to zero only if a command is given to terminal no.4 or c3. 

To launch the remote battery test, send a pulse to terminal no. 5 with sounder on rest mode. This way, a 30-seconds 

test runs.

 

ANOMALY TYPE

LD4 LED

Speaker interruption (test performed every 10 s)

1 flash

No recharge current (recharge current is lower than 12V)
(test performerd every 10 s)

2 flashes

Battery is disconnected (test performerd every 10 s)

3 flashes

Battery voltage is low (recharge is lower than 10V)
(test performed every 10 s) 

4 flashes

Battery low-capacity, deterioration
(test performed every 22 hours)

5 flashes

No anomalies

OFF

Test battery in progress

Fast

FLASH RESET / BLOCK SPEAKER INPUT

 

With DIP6 in OFF, terminal 5 works as block speaker. With DIP6 in ON, terminal 5 works as reset flash: the flashing 
unit activates with sounder trigger and deactivates with terminal 5. During normal operation, a command to terminal 
5 activates battery test that lasts 30 seconds. 

Содержание GIUDECCA









Отзывы: