background image

 

© 2007 

American Hotrod Manufacturing, LLC • 2220 Eastridge Avenue Riverside, CA 92507 

 

- 66 - 

PARTS AND LABOR NOT COVERED 

 

Only the Covered Components detailed above are warranted. Among items not covered are the following: 

 

Battery; cables; primary and final drive belts; brake friction material; bulbs, exhaust system; 

 

Exhaust and muffler cosmetics. There is no warranty on exhaust pipes and mufflers with regard to any 
discoloration. Discoloration (“bluing”) is caused by tuning characteristics, cam timing, carburetor jetting and 
overheating and is not caused by defective manufacturing. 

 

Fastening devices (bolts, clips, nuts, pins and screws);  

 

Filters; fluids; bulbs; lamps; lenses; rubber materials (grommets, floor boards grips, hand grips, brake and 
shifter lever grips, covers); 

 

Seat upholstery; spark plugs; tires; tune-up parts; 

 

Any accessory if altered, tampered with, or not manufacturer installed; 

 

Damage caused by exceeding manufacturer's recommended weight and/or recommended rider limits; 

 

Any regular maintenance services; 

 

Damage resulting from inadequate fluid levels or use of improper fluids; 

 

Any Covered Component that has no defect; 

 

Any mechanical adjustments, tune-ups, alignments, storage, or taxes. 

 

Any component that has failed due to abuse, misuse, racing, neglect or negligence. 

 

Other than defects identified during the first 6 months, chrome does not carry a warranty. Rust and scratches 
are not caused by defective manufacturing. 

 
In cases of disputes or questions arising over the interpretation of warranty applicability or procedures to correct a 
warranted item or system, American Hotrod Manufacturing, LLC reserves the right to inspect and diagnose the 
motorcycle at a location of its choice, including return to the factory. 
 

LIMITED LIABILITY – LEGAL RIGHTS 

 

Claims resulting from external causes such as vandalism; theft or attempted theft; collision; rust; corrosion; 
deterioration; punctures; acts of God such as fire, smoke, water, snow, flood, freezing, hail, windstorm, 
earthquake, explosion, lightning, falling objects; delay or failures in authorized repair and/or replacement 
services from the aforementioned causes, or other causes beyond American Hotrod Manufacturing, LLC’s 
control, are not covered.  

 

 

Engine repairs, other than those authorized by American Hotrod Manufacturing, LLC for corrective purposes, 
are not covered. 

 

 

Damage to paint from any cause, other than factory defect, is not covered. Damage to chrome from any 
cause, other than factory defect is not covered. 

 

 

This Manufacturer's Limited Warranty is in lieu of all other warranties, whether oral, written, expressed, or 
implied. There are no warranties of merchantability or fitness for a particular use or purpose. American Hotrod 
Manufacturing, LLC’s obligations and Owner's remedies hereunder are solely and exclusively as stated. 
American Hotrod Manufacturing, LLC’s liability for incidental and consequential damages including but not 
limited to, personal injury, physical damage, property damage, loss of use of the motorcycle, loss of time, 
inconvenience, and commercial loss resulting from the operation, maintenance, or use of the motorcycle is 
expressly excluded. Some states do not allow limitations on how long an implied warranty lasts, or allow the 
exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to you. 
This warranty gives you specific legal rights and you may also have other rights, which vary from state to 
state.  

 

 

To obtain performance under this Manufacturer's limited Warranty, OWNER must either return the motorcycle 
at OWNER'S expense to an authorized dealer or service center. 

Содержание 2007 Hotrod Bones















































































Отзывы: