background image

Round Fire and Combination Fire Smoke Dampers

1

Document 483515

Fire and Combination Fire Smoke Dampers

DFDR-XXX, FDR-XXX, FSDR-XXX, SEDFDR-XXX, 

SEFSDR-XXX, SSDFDR-XXX, SSFDR-XXX, 

SSFSDR-XXX Series

1

1

2

 Hour

Installation, Operation and Maintenance Manual

Please read and save these instructions for future reference. Read carefully before attempting to assemble, install, 
operate or maintain the product described. Protect yourself and others by observing all safety information. Failure 
to comply with these instructions will result in voiding of the product warranty and may result in personal injury 
and/or property damage.

These instructions apply to 1

1

2

 hour rated fire and 

combination fire smoke dampers mounted in: 1) 
masonry, block, or stud walls and 2) concrete floors or 
ceilings. Specific requirements in these instructions are 
mandatory. Dampers must be installed in accordance 
with these instructions to meet the requirements of 
UL 555 and/or UL 555S.

Receiving and Handling

Upon receiving dampers, check for both obvious 
and hidden damage. If damage is found, record all 
necessary information on the bill of lading and file 
a claim with the final carrier. Check to be sure that 
all parts of the shipment, including accessories, are 
accounted for.
Dampers must be kept dry and clean. Indoor storage 
and protection from dirt, dust, and the weather is 
highly recommended. Do not store at temperatures in 
excess of 100°F (38°C).

SAFETY WARNING

Improper installation, adjustment, alteration, service 
or maintenance can cause property damage, injury 
or death. Read the installation, operating, and 
maintenance instructions thoroughly before installing 
or servicing this equipment.

Table of Contents

General Information . . . . . . . . . . . . . . . . . . 2
Electrical Guidelines . . . . . . . . . . . . . . . . . . 2
Pre-Installation Guidelines .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   2
Preparation of Openings .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   3
Clearances Required Between Damper Sleeves and 
Wall/Floor Openings . . . . . . . . . . . . . . . . . . 4
Inserting Damper into Wall/Floor Openings . . . . . . 5
Securing the Damper/Sleeve Assembly to Wall and 
Floor Openings.   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   6
Duct to Sleeve Connections .   .   .   .   .   .   .   .   .   .   .   .   .   .   6
Actuator and Temperature Response Device 
Connections . . . . . . . . . . . . . . . . . . . . . . 6
Blade Orientation  . . . . . . . . . . . . . . . . . . . 8
Damper Maintenance . . . . . . . . . . . . . . . . . 8
Damper Troubleshooting.   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   8

Содержание DFDR Series









Отзывы: