manualshive.com logo in svg
background image

assembly 

hints

1. Assembly  (Skipping this can lead to troubles ! )

Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.

1.1 Make sure you have the right tools:

• 

A good quality soldering iron (25-40W) with a small tip.

• 

Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called ‘thinning’ and 
will protect the tip, and enables you to make good connections.  When solder rolls off  the tip, it needs cleaning.

•  Thin raisin-core solder. Do not use any flux or grease.

•  A diagonal cutter to trim excess wires. To avoid injury when cutting excess  leads, hold the lead so they cannot 

 

fly towards the eyes.

• 

Needle nose pliers, for bending leads, or to hold components in place.

•  Small blade and Phillips screwdrivers. A basic range is fine.

 

)

For some projects, a basic multi-meter is required, or might be handy

1.2 Assembly Hints :

•  Make sure the skill level matches your experience, to avoid disappointments.

• 

Follow the instructions carefully. Read and understand the entire step before you perform each operation. 

• 

Perform the assembly in the correct order as stated in this manual

• 

Position all parts on the PCB (Printed Circuit Board) as shown on the drawings. 

• 

Values on the circuit diagram are subject to changes, the values in this assembly guide are correct*

•  Use the check-boxes to mark your progress.

• 

Please read the included information on safety and customer service

* Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as ‘NOTE’ on a separate leaflet.  

1.3 Soldering Hints :

1.  Mount the component against the PCB surface and carefully solder the leads

2.  Make sure the solder joints are cone-shaped and shiny

3. 

Trim excess leads as close as possible to the solder joint

- 5 -

- 4 -

DO NOT BLINDLY FOLLOW THE ORDER OF THE 

COMPONENTS ONTO THE TAPE. ALWAYS CHECK THEIR 

VALUE ON THE PARTS LIST!

���������������

���������������������

Содержание K8093

















Отзывы: