VELFORM FULL BODY RAZOR, Инструкция по эксплуатации

Страница: 8 / 36

8
could cause them to short-circuit.
• Do not allow children to play with batteries.
• Do not tamper with the device in any way. The
device should be handled or repaired only by an
authorized professional.
• This product should not be used by anyone
(including children) with reduced physical,
sensory or mental abilities, or by people without
adequate experience or knowledge, unless they
are supervised by someone responsible for
their safety or are given instructions on how to
use the device. Children should be supervised
to ensure they do not play with the product.
• Do not use the product for any purpose not
recommended in this manual.
2. COMPONENTS
A1. ON/OFF button
B. Trimming guides
C1. Blade
C2. Blade release button
C3. Built-in LED
D. Blade shield
E. Cleaning brush
3. The Set Contains:
A. Velform® Full Body Razor
B. 3 trimming guides (1 mm, 3 mm, 5 mm)
C. 1 cutting head
D. 1 blade shield
• 1 instruction manual
4. INSTRUCTIONS FOR USE
Battery Installation
- Runs on one 1.5 V AA battery.
- Remove the blade by following the instructions in the
“Changing the Blades” section.
- To open the battery compartment, slide the cover in the
direction of the arrow.
- Insert the battery by matching the polarity markings in
the compartment.
- Put the cover back in place and ensure it is firmly closed.
- Reattach the blade.
NOTE: Before using the device for the first time, try
trimming the hair in a small area on your arm or leg. If you
notice any sensitivity or allergic reactions, discontinue use
immediately.
NOTE: As when using any other hair trimmer or shaver,
be careful to avoid nicks and cuts in sensitive areas like
the ears.
Velform® Full Body Razor is designed for DRY USE
ONLY. Do not use it in the shower or rinse the blades
under water.
• If the blade shield is on the blade, remove it before using
the device (Picture 1). Press the ON/OFF button to switch
the Velform® Full Body Razor on and off (Picture 2).
NOTE: When the device is ON, the LED light should be
on. We recommend leaving the blade shield on the device
when it is not in use.
SHAVING
Perfect for shaving body and facial hair.
• The 5, 3 and 1 mm trimming guides let you trim to the
length and shape you want (see the “Trimming” section).
• To remove unwanted hair in seconds, use the double-
sided blade to trim the desired area by making upward
and downward motions.
• The pivoting head adapts perfectly to the body.
• The LED light helps light up hard-to-reach areas.
TRIMMING
The 5, 3 and 1 mm trimming guides let you trim your beard
to the length you want or maintain the same stubble length
every day (Picture 3).
TRIMS
• Make sure the device is switched off. Choose one of the
trimming guides supplied, place it on the blade and make
sure it is firmly attached (Picture 4).
The bristles can face up or down for ease of use, depending
on the area to be trimmed.
• Do not move the device too quickly. It is better to make
slow, delicate strokes.
• Always trim hair in the direction of the trimming guide
bristles and make sure that the flat part of the guide is in
contact with the skin.
• For best results, try different trimming positions (upward,
downward and side to side) and trim with the blade head
against the direction of hair growth.
• For best results, use the device only when the skin and
hair are completely dry.
SHAPING
The pivoting head with light adapts to the shape of the
face and is designed to offer total control when shaping
your beard (Picture 5).
• DO NOT USE the device with water or shaving cream.
The blade may not work properly.
• Press gently when making long strokes. The skin may
take some time to adapt to the blade.
NOTE: It is normal for the blade head to heat up during
use.
EDGING
Select the preferred trimming guide to edge your