Velbus VMB4RYLD Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 70

Velbus VMB4RYLD Скачать руководство пользователя страница 66

VELBUS INSTALLATION GUIDE

©2015 Velbus

66

www.velbus.eu

All modules with electronic addressing can use the full HEX range of 01-FE (in
decimal notation: 01

–

254).

In any case, check also if there are no wiring problems and restart the system
if necessary (power down, wait a few seconds and power up again).

In case of error, modules may have their LEDs blinking as follows:



blinking 2 x, pause, blinking 2 x, etc: communication error



blinking 3 x, pause, blinking 3 x, etc.: supply voltage too low



blinking 4 x, pause, blinking 4 x, etc.: supply voltage too high

This may vary between modules. Check the documentation of the specific
modules for further details.

An input module stops responding

Check if you haven’t programmed a delay in the button or input channel. Push

the button for at least three seconds to make sure.

The channel may also be locked. In Velbuslink, right click on the channel, select

“this module” > “unlock buttons”.

In case of a static electrical discharge, power down the system, wait a few
seconds and power up again.

A module with electronic addressing remains untraceable (red X next
to its state) in Velbuslink, although the LEDs on the module behave
normally

Check that you have not accidentally changed the address of this module? You
can find the module by opening the detection window in Velbuslink and
physically operate the module. You will see the module appear in Velbuslink
along with its correct address.

After a scan of my new modules I get continuous error messages if I try
to read or sync

All modules with electronic addressing have their address set to FF by factory
default. You must assign a new address to all modules before taking further

«
...
64
65
66
67
68
...
»

Содержание VMB4RYLD







































































Отзывы:

Нет отзывов