Vega VEGAPULS 68 Скачать руководство пользователя страница 71

Страница: 71 / 104

9 Diagnosis, asset management and service

VEGAPULS 68 • Foundation Fieldbus

36538-EN-170405

If you saved the parameter settings during the first setup of the sen-

sor, you can transfer them to the replacement electronics module. A

fresh setup is then not necessary.

9.6 Software update

The following components are required to update the instrument

software:

•

Instrument

•

Voltage supply

•

Interface adapter VEGACONNECT

•

PC with PACTware

•

Current instrument software as file

You can find the current instrument software as well as detailed

information on the procedure in the download area of our homepage:

www.vega.com.

Caution:

Instruments with approvals can be bound to certain software versions.

Therefore make sure that the approval is still effective after a software

update is carried out.
You can find detailed information in the download area at

www.vega.com.

9.7 How to proceed if a repair is necessary

You can find an instrument return form as well as detailed informa-

tion about the procedure in the download area of our homepage:

www.vega.com.
By doing this you help us carry out the repair quickly and without hav-

ing to call back for needed information.
If a repair is necessary, please proceed as follows:

•

Print and fill out one form per instrument

•

Clean the instrument and pack it damage-proof

•

Attach the completed form and, if need be, also a safety data

sheet outside on the packaging

•

Please contact the agency serving you to get the address for

the return shipment. You can find the agency on our home page

www.vega.com.

Содержание VEGAPULS 68









































































































Результаты поиска

Содержание VEGAPULS 68

Отзывы:

Бренды по названию

Популярные бренды

Vega VEGAPULS 68, Руководство по эксплуатации

Результаты поиска

Содержание VEGAPULS 68

Отзывы:

Бренды по названию

Популярные бренды