Vega VEGAPULS 68 Скачать руководство пользователя страница 13

Страница: 13 / 104

3 Product description

VEGAPULS 68 • Foundation Fieldbus

36538-EN-170405

The interface adapter VEGACONNECT enables the connection of

communication-capable instruments to the USB interface of a PC. For

parameter adjustment of these instruments, the adjustment software

PACTware with VEGA-DTM is required.
You can find further information in the operating instructions "

Interface

adapter VEGACONNECT

" (Document-ID 32628).

The VEGADIS 81 is an external display and adjustment unit for VEGA

plics

sensors.

For sensors with double chamber housing the interface adapter

VEGADIS adapter

" is also required for VEGADIS 81.

You can find further information in the operating instructions

VEGADIS 81

" (Document-ID 43814).

The VEGADIS adapter is an accessory part for sensors with double

chamber housings. It enables the connection of VEGADIS 81 to the

sensor housing via an M12 x 1 plug.
You can find further information in the supplementary instructions

VEGADIS adapter

" (Document-ID 45250).

PLICSMOBILE T61 is an external GSM/GPRS radio unit for transmis-

sion of measured values and for remote parameter adjustment of

plics

sensors. Adjustment is carried out via PACTware/DTM and the

integrated USB connection.
You can find further information in the supplementary instructions

PLICSMOBILE T61

" (Document-ID 37700).

PLICSMOBILE is an internal GSM/GPRS radio unit for transmission

of measured values and for remote configuration of plics

sensors.

Adjustment is carried out via PACTware/DTM and the integrated USB

connection.
You can find further information in the supplementary instructions

PLICSMOBILE GSM/GPRS radio module

" (Document-ID 36849).

The overvoltage arrester B81-35 is used in the single or double

chamber housing instead of the connection terminals. It reduces any

voltage surges that may reach the signal cables to a harmless level.
You can find further information in the supplementary instructions

Overvoltage arrester B81-35

" (Document-ID 50708).

The protective cover protects the sensor housing against soiling and

intense heat from solar radiation.
You will find additional information in the supplementary instructions

manual "

Protective cover

" (Document-ID 34296).

Screwed flanges are available in different versions according to the

following standards: DIN 2501, EN 1092-1, BS 10, ASME B 16.5,

JIS B 2210-1984, GOST 12821-80.

VEGACONNECT

VEGADIS 81

VEGADIS adapter

PLICSMOBILE T61

PLICSMOBILE

Overvoltage protection

Protective cover

Flanges

Bluetooth function with VEGADIS 82 can only be used at a later date.

Содержание VEGAPULS 68









































































































Результаты поиска

Содержание VEGAPULS 68

Отзывы:

Бренды по названию

Популярные бренды

Vega VEGAPULS 68, Руководство по эксплуатации

Результаты поиска

Содержание VEGAPULS 68

Отзывы:

Бренды по названию

Популярные бренды