Vega VEGAPULS 68 Скачать руководство пользователя страница 57

Страница: 57 / 104

6 Set up with the display and adjustment module

VEGAPULS 68 • Foundation Fieldbus

36538-EN-170405

•

Setup:

Resetting of the parameter settings to the default values of

the respective instrument . Order-related settings remain but are

not taken over into the current parameters. User-generated false

signal suppression, user-programmed linearization curve, meas-

ured value memory, echo curve memory as well as event memory

remain untouched. The linearization is set to linear.

•

False signal suppression:

Deletes a previously created false

signal suppression. The false signal suppression created at the

factory remains active.

•

Peak values, measured value:

Resets the measured min. and

max. distances to the current measured value.

Select the requested reset function

[->]

and confirm with

[OK]

The following table shows the default values of VEGAPULS 68:

Menu section

Menu item

Default value

Setup

Measurement loop name

Sensor

Medium

Liquid/Water
Bulk solids/Crushed stones, gravel

Application

Storage tank
Silo

Vessel form

Vessel bottom, dished form
Vessel top, dished form

Vessel height/Measur-

ing range

Recommended measuring range, see "

Technical data

in the supplement

Min. adjustment

Recommended measuring range, see "

Technical data

in the supplement

Damping

0.0 s

Display

Language

Like order

Displayed value

Distance

Display unit

m(d)

Scaling

0.00 %, 0 l
100.00 %, 100 l

Backlight

Switched on

Additional settings

Distance unit

Temperature unit

°C

Unit SV2

Probe length

Length of standpipe ex factory

Linearisation curve

Linear

The instrument settings are copied with this function. The following

functions are available:

•

Store data from sensor in the display and adjustment module.

•

Store data from display and adjustment module in the sensor

Additional settings - Copy

instrument settings

Содержание VEGAPULS 68









































































































Результаты поиска

Содержание VEGAPULS 68

Отзывы:

Бренды по названию

Популярные бренды

Vega VEGAPULS 68, Руководство по эксплуатации

Результаты поиска

Содержание VEGAPULS 68

Отзывы:

Бренды по названию

Популярные бренды