manualshive.com logo in svg

Vega VEGACAP 35, Руководство по эксплуатации

Поделиться
Скачать
Vega VEGACAP 35 Скачать руководство пользователя страница 24

24

7 Diagnostics and servicing

VEGACAP 35 • Relay (DPDT)

33759-EN-230510

7.  Open the tensile ring on the old electronics module and pull out 

the old electronics module.

8.  Compare the new electronics module with the old one. The type 

label of the electronics module must correspond to that of the old 

electronics module.

9.  Insert the new electronics module.
10.  Screw in and tighten the two screws with a Torx screwdriver.
11.  Lead the connection cable through the cable gland.
12.  Insert the wire ends into the open terminals according to the wir-

ing plan and tighten them.

13.  Check the hold of the wires in the terminals by lightly pulling on 

them.

14.  Tighten cable gland and check on tightness. The seal ring must 

completely encircle the cable.

15.  Carry out a fresh adjustment. See chapter " 

Set up, new adjust-

ment

". 

16.  Screw the housing lid back on

The electronics exchange is now finished.

7.4  Shortening of the probe

The cable of the probe can be shortened individually.

Содержание VEGACAP 35





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды