Vega VEGABAR 38 Скачать руководство пользователя страница 44

Страница: 44 / 68

10 Diagnostics and servicing

VEGABAR 38 • Three-wire with IO-Link (2 x transistor or 4 … 20 mA plus 1 x transistor)

57532-EN-191014

•

Out of specification

•

Maintenance requirement

and explained by pictographs:

Fig. 27: Pictographs of the status messages
1 Failure - red

2 Out of specification - yellow

3 Function check - orange

4 Maintenance - blue

Failure:

Due to a malfunction in the instrument, a fault message is

output.
This status message is always active. It cannot be deactivated by the

user.

Function check:

The instrument is being worked on, the measured

value is temporarily invalid (for example during simulation).
This status message is inactive by default.
Out of specification: The measured value is unreliable because an

instrument specification was exceeded (e.g. electronics temperature).

This status message is inactive by default.

Maintenance:

Due to external influences, the instrument function

is limited. The measurement is affected, but the measured value is

still valid. Plan in maintenance for the instrument because a failure is

expected in the near future (e.g. due to buildup).
This status message is inactive by default.

Code
Text message

Cause

Rectification

F013
no measured value available

Hardware error in the area of the meas-

uring cell

Send instrument for repair

F017
Adjustment span too small

Adjustment not within specification

Change adjustment

F036
no operable sensor software

Failed or interrupted software update

Repeat software update

F080
General software error

General software error

Restart

F110
Switching points too close to-

gether

Selected switching points too close to-

gether

Increase the distance between the

switching points

Failure

Содержание VEGABAR 38





































































Результаты поиска

Содержание VEGABAR 38

Отзывы:

Похожие инструкции для VEGABAR 38

Бренды по названию

Популярные бренды

Vega VEGABAR 38, Руководство по эксплуатации

Результаты поиска

Содержание VEGABAR 38

Отзывы:

Похожие инструкции для VEGABAR 38

Бренды по названию

Популярные бренды