background image

Q700

4

Table of Contents

Quick Setup . . . . . . . . . . . . . . . . . . . . . . .2

MS-700 Controls and Indicators  . . . . . .5

Front Panel  . . . . . . . . . . . . . . . . . . . . .5
Rear Panel . . . . . . . . . . . . . . . . . . . . . .6

Programming System Frequencies  . . . . .7

via Front Panel Controls . . . . . . . . . . .7
via QPK-1 Kit and Software . . . . . . . .8

Programming Beltpack Frequencies  . . . .9

Locking the MS-700 Control Panel  . . . .9

Changing the Software Password . . . . . .9

Programming Beltpack Mode  . . . . . . . .10

via Panel/Pushbuttons  . . . . . . . . . . .10
via QPK-1 Kit and Software . . . . . . .12

Beltpack Batteries  . . . . . . . . . . . . . . . . .13

Battery Information  . . . . . . . . . . . . .13
Installing Batteries  . . . . . . . . . . . . . .13

System Operation and Features  . . . . . .14

System Operation . . . . . . . . . . . . . . .14
Operational Features  . . . . . . . . . . . .14
BP-700 Headset Compatibility . . . . .15

Specifications  . . . . . . . . . . . . . . . . . . . .16

A word to Vega Users

In selecting a Vega intercom system, you
are assured of the highest quality and
performance. Vega has been the leader
in wireless intercom systems for well
over a decade. This experience insures
you of a Vega Intercom System of
quality, performance and reliability.

Unpacking

Verify the number of boxes shown
“as shipped” and that all have been
received in good condition. Unpack your
equipment, saving all cartons for
storage or reshipping. If, for any reason,
you do not find the equipment to be
completely satisfactory, please
immediately contact your Vega dealer or
the Vega factory.

Should service ever be required,

remember your authorized Vega service
dealer knows your equipment best. they
have the training and test equipment
necessary to restore your equipment to
its’ peak performance.

And of course, please feel free to

contact either your authorized Vega
dealer or the Vega factory for
information or assistance at any time.

Содержание Q700

















Отзывы: