background image

Introduction

Safety Precautions

2

In addition to the specified torque values noted in this manual, when properly tightened, all flanged fittings should 
have metal-to-metal contact.

WARNING

This product operates in the highly combustible atmosphere of a gasoline storage 
tank.

FAILURE TO COMPLY WITH THE FOLLOWING WARNINGS AND SAFETY 
PRECAUTIONS COULD CAUSE DAMAGE TO PROPERTY, ENVIRONMENT, 
RESULTING IN SERIOUS INJURY OR DEATH.

1. All installation work must comply with the latest issue of the National 

Electrical Code (NFPA 70), the Code for Motor Fuel Dispensing Facilities and 
Repair Garages (NFPA 30A), and any European, national, state, and local 
code requirements that apply.

2. Turn off, tag, and lockout power to the STP before connecting or servicing the 

STP.

3. Before installing pipe threads apply an adequate amount of fresh, UL 

classified for petroleum, non-setting thread sealant.

4. When servicing unit, use non-sparking tools and use caution when removing 

or installing equipment to avoid generating a spark.

5. To protect yourself and others from serious injury, death, or substantial 

property damage, carefully read and follow all warnings and instructions in 
this manual. 

OFF

Содержание Red Jacket Maxxum Big-Flo Quick-Set Series



















































Отзывы: