background image

01/14

1-10

10

20

21

22

2

1

GB

INSTALLATION INSTRUCTIONS: Viewline 85 mm

TU00-0752-5807102

Technische Änderungen vorbehalten  -  Technical details subject to change

TU00-0752-5807102

Tachometer

To remove the connector, press the latch (

1

) and pull 

the connector out (

2

). 

Important:

 Clean the instrument glass and front frame with water only. Do not use chemical agents.

Accessories / Spare parts 

Bush contacts 0.25 – 0.5 mm²   A2C59510846

Bush housing, 8-pin  

A2C59510847

Bush housing, 14-pin  

A2C59510848

Hand pliers  

Tyco No. 539635-1

Tool for hand pliers  

Tyco No. 539682-2.

Single contacts 0.14 – 0.22 mm²   Tyco No. 1355718-1

Single contacts 0.5 – 0.75 mm²   Tyco No. 963729-1

Strip 0.14 – 0.22 mm²  

Tyco No. 1355717-1

Strip 0.25 – 0.5 mm²  

Tyco No. 928999-1

Strip 0.5 – 0.75 mm²  

Tyco No. 963715-1

Bracket assembly mounting set   A2C59510854

Flush mount fixing bracket  

A2C59510864

Flush mount seal  

A2C53215641

Fastening nut  

A2C53212238

Front ring, flat; black  

A2C53192911

Front ring, flat; white  

A2C53192912

Front ring, flat; chrome  

A2C53192910

Front ring, triangular; black  

A2C53192917

Front ring, triangular; white  

A2C53192920

Front ring, triangular; chrome  

A2C53192918

Front ring, round; black  

A2C53192913

Front ring, round; white  

A2C53192916

Front ring, round; chrome  

A2C53192914

Protective connector cap, 8-pin  A2C53324664

Protective connector cap, 14-pin  A2C53324671

Содержание TU00-0752-5807102












Отзывы: