![background image](http://html.mh-extra.com/html/vdo/cancockpit-series/cancockpit-series_product-manual_858176023.webp)
Technische Änderungen vorbehalten Technical details subject to change
2 - 13
TU00-0726-0000002
0609
The display is structured into three main areas:
1. Symbol Area
This 30 x 32 pixel area is reserved for graphic symbols. The symbols are left aligned to optically enlarge the appearance of
the symbol.
2. Central Area
The centre of the display is organised as one or two lines with 6 digits each. Here it is possible to show alphanumeric ASCII
characters using the large font (12 x 16 pixel). If only one line is displayed, then this line will be centred in vertical direction.
Short text (up to 6 letters) can be used to provide identification for the value displayed. This area is best suited to communi-
cate important numeric values to the user. Values will be shown in the second line on the right, where units appear on the left.
One or two centre lines are configured via WINgauge as well as the description of the short text.
3. Physical Unit Area
The physical unit area is located right of the alphanumeric Centre Lines. In general the unit belonging to the value displayed
on the centre lines is shown here as text. This area is organised as four lines of 5 characters of the small font. If the Unit can
be displayed with less than three ASCII characters, then the large font is applied, else the small font is used. Units will not be
wrapped into the next line.
If there are two Centre Lines, then there will also be two-unit Lines (small Line 2 and Line 4). In case only one Centre Line is
displayed, then only one corresponding Unit Line will be visible (small Line 3).
It is therefore possible to show the following parameters and units to give a clear indication of the valid physical unit which
can be chosen via WINgauge:
2. Functional Specification
Product Manual
24 * 24
12 * 16
6 * 8
30 dots
72 dots
30 dots
32
d
o
ts
Dot Matrix Layout
One centre Line or
optional two Alphanumeric Lines
with 6digits (12*16dots) each
Four Alphanumeric
Lines with 5 digits each
Graphic
Symbol Area
Parameter
Units
Revolution / rotation
1/min, rpm
Speed
km/h, mph, knots
Distances
km, m (Meter), mm, miles, mi, M, m (landmile = 1.609 km), nm (nautical mile = 1.852 km)
Power supply
Volt, V, A, mA
Time
h, hours, min, sec
Temperatures
°C, °F
Pressures
bar, psi, kPa, Mpa,
Level of liquids
%, l, gal (US-gallons)
Fuel consumption
l/h, gal/h, km/l, l/100, kg/h, km/kg
Weight
kg
Power
N, kN, Nm
Diverse
Ohm, Grad, deg, appl, Count, qm/h, Gear, Code, SPN, FMI
Содержание CANcockpit Series
