background image

K6/K6N Vacuum Packaging Machine 

Interface definition  

 

 

 
 

 

 
2002-04-25  

Art. no. 519.340  

Page 1 7/56  

6  Interface definition 

6.1 

Electrical connection 

The electrical data for the machine is shown on the rating plate, which is located on the back of the 
machine. 
 
Also refer to the information contained under ”Technical data“ and the circuit diagrams in the section on 
“Diagrams”. 
 

 

DANGER 

The machine may only be connected to the mains by a qualified expert (electrician), complying 
with local regulations! The procedure for electrical installation is described in the section on the 
“Installation of the machine”. 

 

6.2 

Inert gas connection  

Only in the K6N machines 

The owner must ensure that there is an inert gas 
supply available. 
 
The inert gas is fed via a hose from the pressure 
reducer unit (2) on the gas cylinder (1) to the inert 
gas valve (3) in the machine. 
 
The procedure for connecting the inert gas line on 
the machine is described under “Inert gas installation” 
in the section on ”Installation of the machine“. 

 

Fig. 6/1 

 

 

IMPORTANT  

If there is no gas cylinder connected in the K6N machine, set the “Inert gas” parameter in the 
service program to OFF (0). Otherwise, air can leak into the packaging bag! For more 
information read the sub -section on the “Service program” in the section on “Programming”. 

 

Inert gas quality 

For more information on this read “Processing materials” in the section on “Safety”. This contains 
information on the permissible types of inert gas. 
 

 

DANGER 

Only use a different inert gas with the prior consent of the machine manufacturer. Explosive 
gases or a gas which may be harmful to the operator if inhaled are prohibited, in particular. 

Содержание K6

























































Отзывы: