background image

Outputs: Digital Setup Menu (Channel 1 and 2)

OUTPUT

Press ’■’ and then use the ‘◄’ and ‘►’ buttons to associate either of the following channels
SPEED, SLIP, PITCH, ROLL, LAT ACC and LONG ACC to the Digital output. Then press ’■’ to
confirm.

PULSES
PER METER

Only available when output is set to SPEED.

Press ’■’ and then use the ‘◄’ and ‘►’ buttons to set the number of pulses per revolution. Then
press ’■’ to confirm.
0.1 – 120 (0.1 Steps)

MAX SPEED

Only available when output is set to SPEED.

Press ■’ and then use the ‘◄’ and ‘►’ buttons to set the maximum Speed. Then press ’■’ to
confirm.

0 – 400 km/h (1 km/h steps)

MAX VALUE

Only available when output is set to LAT ACC, LONG ACC, PITCH, SLIP or ROLL

Press ’■’ and then use the ‘◄’ and ‘►’ buttons to set the maximum value of that channel. Then
press ’■’ to confirm.

0 – 180

o

(1

o

steps) for Slip

0 – 90

o

(1

o

steps) for Pitch

0 – 90

o

(1

o

steps) for Roll

0.5 – 2 g (0.1 g steps) for LAT ACC
0.5 – 2 g (0.1 g steps) for LONG ACC

MAX
FREQUENCY

Only available when output is set to LAT ACC, LONG ACC, PITCH, SLIP or ROLL

Press ’■’ and then use the ‘◄’ and ‘►’ buttons to set the maximum Frequency used on the digital
output. Then press ’■’ to confirm.
1 – 50 kHz (0.1 kHz steps)

TEST

Press ’■’ and then use the ‘◄’ and ‘►’ buttons to set a test value that the Digital output will
simulate. Then press ’■’ to quit.

EXIT

Press ’■’ to exit the setup menu and cause the settings to be saved in EEPROM

8

Содержание II












Отзывы: