Page 4 / 6
4. 3 HOURS (3H) MODE (nighttime operation only)
Select “3H” on mode switch, slide the Time switch to the desired shut-off delay time setting
(30s/1min/3min),
select the Low Level brightness level (between 0
~
50%) and CCT (between 2200
~
5
0
00K).
● At dusk, the light will turns on in early evening mode at full brightness (100%) and pre-selected CCT
(2200K~5000K), and remain at those settings for 3 hours
.
● After the 3 hours the light will transition to late night setting and initiate motion sensor operation.
During late night setting, the light will transition
to selected low level brightness (0~50%) and CCT
(2200K~5000K)
and brighten instantly whenever motion is detected.
When motion is detected, the light turns to full brightness (100%) and stays on as long as motion continues.
When motion is no longer detected, the light will remain on at full brightness (5000K) for the predetermined time
you set (30s/1min/3min), and then automatically switch back to selected low-level brightness (0~50%) and CCT
(2200~5000K) settings.
● At dawn, the light turns off automatically.
Note: The low-level brightness and CCT color settings are adjustable by using the low-level brightness
(0~50%) knob and CCT color (2200K~5000K) knob on the bottom portion of the backplate (See Fig.6)
5. CUSTOM MODE (nighttime operation only):
● Select "CUSTOM" on mode switch, slide the Time switch to the desired shut-off delay time setting
(30s/1min/3min), select the Low Level brightness level (between 0
~
50%) and CCT (between 2200
~
500
0
K).
● At dusk, the light will initially turn on in early evening setting, at full brightness
and selected CCT
(2
2
00K
~ 5000K
),
and off at dawn
automatically.
● To set a specific time for the light to transition into late night setting and initiate motion sensor operation you will
utilize the wall switch to which the light is connected. During late night setting, the light will transition to selected
low level setting (0~50% brightness) and CCT setting (2200~5000K) and brightens instantly to full brightness at
5000K whenever motion is detected.
● To set the specific transition time, turn the wall switch to "OFF" and back to "ON" two times within 3 seconds.
The light will remember that time and go into late night setting/motion-sensor operation at that specified time every
night.
● When motion is detected, the light turns to full brightness (5000K) and stays on as long as motion continues.
When motion is no longer detected, the light will remain on at full brightness (5000K) for the predetermined time
you set (30s/1min/3min), and then automatically switch back to selected low-level brightness (0~50%) and CCT
(2200~5000K) settings.
● To revert the light back to Default, turn the wall switch "OFF" and then turn it back "ON" after 5 seconds.
6.
MANUAL OVERRIDE
(nighttime operation only)
● To temporarily override the settings in "AUTO" or "3H" mode
for on-demand continuous high-level brightness at night,
turn the wall switch "OFF" and then "ON" twice within 3
seconds., The light will then remains on all night long.
● To shift back to "AUTO" or "3H" mode, turn the wall switch
"OFF" and then “ON” twice within 3 seconds again. (See Fig.7)
● The light automatically turns off at dawn.
7. CCT
COLOR SWITCHING
● CCT Color adjustable function apply to low-level brightness in Auto mode when no motion is detected, and during
the start of 3H, PC, and Custom mode.
Note: To make sure the above functions operate properly, always keep the wall switch in
the
″ON″
position (including the daytime).
Fig. 7
"AUTO" or
"3H" Mode
Manual
Override
Manual Override Operation Diagram
Turn wall switch OFF-ON-OFF-ON
in 0.5~3 Seconds
Turn wall switch OFF-ON-OFF-ON
in 0.5~3 Seconds
220207
Note: The default setting will be the same function as "PC Mode" if no specific transition time is set.
You can also adjust the low-level brightness (0~50%) and CCT color (2200K~5000K) by using the low-level
brightness (0~50%) knob and CCT color (2200K~5000K) knob on the bottom portion of the backplate (See Fig.6)
● For example, a homeowner wants to have the light stay on at full brightness (2700K) from dusk to 8pm and would
then like the light to go into late night/motion sensor mode from 8pm until dawn. To achieve this, the homeowner
turn the wall switch "OFF" and "ON" twice within 3 seconds at 8pm. This sets the time the light goes into late night/
motion sensor mode every day at 8pm.
●