Vaxcel T0274 Скачать руководство пользователя страница 3

Page 3 /  10

 

Function and Operation

Choose a mode by sliding the switch on the bottom of the sensor.  (See Fig.6)

Note: When power is first applied, the light will turn on to 100% brightness. The sensor will take 30 seconds 

to warm up.

1. Test mode (daytime or nighttime operation )

    ● Slide the switch on the left side of the sensor to the “TEST” position.

       (See Fig.6)

    ● With the power on, the light turn

s to low-level brightness 

       automatically.

    ● The light turns to high-level brightness when motion is detected, 

        and stays on as long as the motion continues. Then it reverts back 

        to low-level brightness about 5 seconds after motion is no longer 

        detected.

 Note: You can adjust the low-level (0~50%) and high-level (50~100%)

 brightness by using the brightness switch on the back plate. 

 (See Fig. 7)

2. AUTO MODE (nighttime operation only) 

    ● 

To shift to “AUTO” mode, slide Time Delay switch to the desired 

        time setting (between 5 seconds and 5 minutes). At dusk, the light

        turns on to pre-selected low-level brightness. When motion is 

        detected, the light turns to pre-selected high-level brightness and 

        stays on as long as motion continues. When the motion is no longer

        detected, the light at high-level brightness remains on for the 

        predetermined time you set (5s ~ 5min), and then switches back to 

        low level automatically.

     ● The light turns off automatically at dawn.

Note: You can adjust the low-level (0~50%) and high-level (50~100%)

brightness by using the brightness switch on the back plate. 

(See Fig. 7)

Adjustment Sensor Lower For Short Coverage

Adjustment Sensor Higher For Long Coverage

Fig. 5

1. Gently grasp the light heads and tilt them up or down, left or right to 

    adjust the light coverage area. Keep the light heads at least 1˝ (25mm) 

    away from the sensor.(See Fig. 5)

2. 

Keep the light heads 30˚ below horizontal to avoid water damage and 

    electrical shock.

Fig. 3

Fig. 4

Adjusting the Light Head: 

Fig. 6

Fig. 7

Sensitivity of Motion Sensor 

     ●  You can adjust the sensitivity of the motion sensor by using the “SENSITIVITY” selector located on the right side 

          of the bottom surface of the sensor. (See Fig. 6)

     ●   Adjust motion sensor sensitivity to HIGH (H), MEDIUM (M), or LOW (L) to achieve desired performance.

     ●   Approximate range for each setting: 25 ft. (L), 45 ft. (M), 70 ft. (H).

2. You can rotate the sensor head up and down to change the coverage area (See Fig. 2). Walk through the detection 

     zone at the farthest distance you wish to detect motion.

    

Note: Range set too high may increase false triggering.

 (See Fig. 3 and Fig. 4)

160826

Mode

Mode

HIGH LEVEL

75%

25%

100%

50%

50%

0

LOW LEVEL

TEST

AUTO

RESET

3MIN

1MIN

5S

5MIN

L

M

H

CUSTOM

SETTINGS

SENSITIVITY

Sensitivity

Содержание T0274











Отзывы: