background image

6

Vax Service line

AU: 1300 361 505 / NZ: 0800 800 900

Operation

Carpet Height Adjustment

Settings

Agitator Brush Roll Shut-Off

Cleaning Tools

The cleaning of carpet and rugs takes place at the nozzle (

A

). When it is 

necessary to raise and lower the nozzle for various carpet pile heights,

turn the nozzle control knob (

B

) to the desired setting.

For maximum cleaning performance, the following carpet height settings

are recommended:

• Lowest setting: for all types of carpet.

Note:

 If the cleaner is diffi cult to push, turn knob to the next higher setting.

•  Higher settings: for very deep pile carpet, where easier pushing effort is 

desired, while maintaining good cleaning performance.

The agitator brush roll shuts off automatically for tool use, when the cleaner 

is in the upright position.

To manually shut off the agitator brush roll for cleaning hard fl oors, step on 

the pedal (

A

). The indicator (

B

) will show red in the “brush roll off” window. 

To turn the agitator brush roll on, step on the pedal again. The indicator will 

show red in the “brush roll on” window.

Tools allow for cleaning surfaces above the fl oor and for reaching hard to clean areas.

The cleaner is ready for tool use when handle is in upright position.

The agitator brush roll will not rotate when the cleaner is in the upright position or the if the agitator brush 

roll shut off indicator is in the OFF position when the handle is lowered.

IMPORTANT:

 

Turn brush bar off when cleaning hard fl oors.

B

A

A

B

Содержание Power Plus 6





















Отзывы: