Vax 88000 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 16

Vax 88000 Скачать руководство пользователя страница 4

Vax Service line

AU: 1300 361 505 / NZ: 0800 800 900

3

Operation

Assembling your carpet washer

Align tabs on tool
caddy with slots on
midsection and snap
into place.

Stand the base in the
upright position.
Assemble the mid
section onto the base,
taking care not to trap
internal mains wire.

(Phillips screwdriver required)

Tool Caddy Assembly

(Phillips screwdriver required)

Insert the two nuts into
the recesses located
on the left and right
sides of the base. While
holding the nuts in
place, insert the two
medium length screws
through the front of the
mid section and
tighten.

Slide upper handle down onto the unit. Insert
nut into the recess in the back of the upper
handle. While holding the nut in place, insert
the long screw through the front of the upper
handle and tighten. Run the mains wire
above the upper cord hook and secure
with the cord clip.

Place nut into recess on tool caddy and hold into
place. Press handle release with your other hand
to tilt the mid section backwards.

Place screw through
centre of lower
midsection and tighten.

«
...
2
3
4
5
6
...
»

Содержание 88000

















Отзывы:

Нет отзывов