background image

40

Does the upper duct pipe need to be positioned in a 
2 degree angle?

No, this can be level but it is no problem to 
mount it under a 2 degree angle, the upper 
duct does not drain any condensate, it only 
guides incoming air.

Can we change the door to swing direction?

Yes, by removing the 2 hinge bolds & nuts and 
mounting them on the other side.

Should we first mount the upper and lower duct on 

the unit and then mount the unibody in the wall?

Yes, because the connection of the PVC needs 
to be checked visually before mounting the 
fresh-r

®

 in the wall.

There are more holes in the mounting brackets 
than plugs & screws provided, can we choose which 
mounting bracket holes to use?

Yes, you can choose the holes that give best 
mounting option.

How can we mount the mounting brackets in the 
correct position?

By using the the drilling template.

What should we do with bag C?

This is a spare part kit, store it at the bottom 
of the unit.

After installation

Does the fresh-r

®

 start in the automatic program?

Yes, it always runs in automatic mode, except 
when the fan speed is changed manually. After 
100 minutes it will go back to automatic mode, 
refer to user manual.

How will the fresh-r

®

 determine at what rate the 

fresh-r

®

 needs to operate?

The higher the CO² level or the RH (relative

humidity) levels the more it will ventilate, refer 
to user manual.

I feel cold air coming out of the bottom, is that 
correct?

Yes, moving air feels colder then stationary air, 
refer to user manual.

How can I operate the unit?

On the control panel, “A” for automatic. 

You can increase or decrease the fan speed 

manually using the fan buttons. Refer to the 
user manual. Increase or lower fans speed 

via the fan buttons; refer to user manual.

What does the smiley tell me?

They indicate the air quality, refer to user 
manual.

Does the unit measure RH or CO²?

Yes, it measures both, please refer to user 
manual.

What maintenance should be done?

Rinse heat exchanger with cold water every 

6 months, and clean upper and lower duct pipe 

every 2 years, refer to user manual.

The unit makes noise, is that correct?

If the orange or red face icon is lighted it is 
correct. The air quality is not good enough and 
it substantially increases the ventilation rate. If 
the green smiley is on and it makes more noise 
then 30 dB(A) it could be very humid inside, 
especially just after construction. If the green 
smiley is on and the building is not humid but 
the unit makes noise for more then 3 hours in 
a row, contact your supplier. Refer to user 
manual.

How can we reduce the noise?

Wait till the green light face lightens. If this 
takes too long, open a window. Refer to user 
manual.

The fresh-r

®

 suddenly starts to make noise, but no 

air is coming into the room, what happens?

If it is freezing outside, it is in defrost mode, 

it de-freezes the heat exchanger by blowing 

warm air out, so it can again work at optimum 

efficiency. If it is not freezing outside and the 

fresh-r

®

 suddenly starts to make noise, 

contact your supplier. Refer to user manual.

Содержание Fresh-r





















































Отзывы: