Vaux Electronics Aris 700 Скачать руководство пользователя страница 9

Страница: 9 / 63

Aris MediaMation Controller Rear Panel

700/720i only:

Antenna Input

(female F-connector) — for connection of the ANT-2 Base-Loaded

Coax Antenna (supplied), either directly to the controller, or via RG-59 or RG-6 coaxial extension cable

for a remotely-located antenna. Optionally, other antenna(s), such as the ANT-3 Folded Dipole, or a

multi-antenna system may be connected. Used for reception of RF remote control commands.

Audio/Video Source Inputs

(phono jacks) — eight input sources for line-level stereo audio;

four of the input sources also provide an input for composite video signals (video on 700/720i only).

Audio/Video Zone Outputs

(phono jacks) — six output sources for line-level stereo audio;

four of the

output sources also provide an output for composite video signals (video on 700/720i only).

The audio outputs are volume/bass/treble/mute controlled within the Aris System and connect to

zone power amplifiers (sized appropriately for each zone).

700/720i only:

PLC

(Power Line Carrier) Interface for X-10® Interface Module (6P4C modular jack).

Aris 720i uses Model X2 interface (TW523). Aris 700 uses Model X1 (PL513) (X2 may be substituted).

The Aris Model 710 does not support X-10 control — no PLC jack provided.

Reset Button

(careful — will restore all factory settings, erase all infrared codes, etc.).

VauxNet

Expansion Port Connector (future use).

VauxSerial

Interface (25-pin DB-25F RS-232 connector). DCE (modem-like) port.

710/720i only:

Modulated

IR Input

(3.5 mm phone jack; tip=data, sleeve=ground) — Internal IR

emitter for connection to IR repeater systems, IR keypads, etc. Fed through a 200-ohm limiting resistor.

720i only:

Accessory Port

(8-pin Mini-DIN jack) (future use)

10.

710/720i only:

VauxControl

Keypad Interface (Unmodulated IR Input) (2.5 mm phone jack).

11.

IR Blaster

— One Infrared Room Blaster Connector (3.5 mm phone jack; tip=data, sleeve=ground)

for connecting a room blaster, amplified multiple-emitter connecting block, or a single or dual IR

emitter. This is the master IR signal; the green light indicates the presence of infrared signal output.

Blaster signal is a positive-going 12V switched signal, fed through a 470-ohm current-limiting resistor.

12.

IR Emitters

— Six IR Emitter Cable Connectors (3.5 mm phone jacks; tip=data, sleeve=ground) for

connecting single or dual infrared emitter cables. These six connectors are factory-configured for

Device-Specific operation (that is, the emitters are active only for the corresponding IR device

selected. Identical source components, such as CD changers or satellite tuners, may be

individually addressed by placing them in different device pages (IR banks).

RC-8 remote control devices: 1 - Tuner, 2 - CD, 3 - Cab/Sat, 4 - VCR 1, 5 - VCR 2, 6 - Laser

(for devices 7/8, use dual emitter in blaster port). The IR Emitter ports may also be configured, via

computer command, for “Zone-Specific” operation, in which they are activated based on the remote

control’s selected zone.

Emitter signal is a positive-going 5V switched signal, fed through a 270-ohm current-limiting resistor.

13.

Power

Adaptor (12 VAC, 1A) jack (2.1mm connector).

Содержание Aris 700
































































Результаты поиска

Содержание Aris 700

Отзывы:

Бренды по названию

Популярные бренды

Vaux Electronics Aris 700, Руководство пользователя

Результаты поиска

Содержание Aris 700

Отзывы:

Бренды по названию

Популярные бренды