background image

14

1

  Hold the trigger in the full brake position while powering 

on the transmitter. The LED flashes rapidly, indicating the 

programming mode is active.

2  throttle end Point

 Continue holding full throttle. Turn the  

TH TRIM knob to adjust the full throttle end point.

3  Brake end Point

 Hold the trigger in the full brake position. 

Turn the TH TRIM knob to adjust the full brake end point. 

Return the trigger to the center position.

4  left Steering end Point

 Hold the steering wheel in the  

full left position. Turn the ST TRIM knob to adjust the left  

end point.

5  right Steering end Point

 Hold the steering wheel in the full 

right position. Turn the ST TRIM knob to adjust the right end 

point. Return the steering wheel to the center position.

6

  Power off the transmitter to save the travel adjust settings.

ChanGInG The TraVel adjusT seTTInGs

 / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /

 

/ / / / / / / / / / / / / / / / / / / / / / / / / / / /

1

  Insert a Bind Plug in the BIND port on the receiver.

2

  Insert a second Bing Plug in the DISABLE port on  

the receiver.

3

  Connect a fully charged battery pack to the ESC.

4

  Power on the ESC. The orange LED flashes, indicating  

the receiver is in bind mode.

5

  Center the ST TRIM and TH TRIM dials on the transmitter.

6

  Press and hold the BIND button while powering on  

the transmitter.

7

  Release the BIND button when the orange LED slowly 

flashes. The transmitter and receiver are linked when  

the orange LED is solid.

8

  Pull the transmitter trigger to Full Throttle.

9

  Push the transmitter trigger to Full Brake, then return  

the trigger to center.

10

  Turn the transmitter steering wheel to Full Right.

11

  Turn the transmitter steering wheel to Full Left, then return 

the steering wheel to center. The orange LED flashes once.

12

  Remove the Bind Plugs, then power off the receiver to  

save the settings.

13

  Power off the transmitter.

dIsablInG The sTabIlITy assIsT FunCTIon

 / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /

 

/ / / / / / / / / / / / / / / / / / / / / / / / / /

The minimum Travel is 75%,  

and the Maximum travel is 150%.

ImporTanT:

 If the travel is changed 

on the DX2E, you must rebind and  

calibrate the SRS4200.

If you participate in organized racing, 

you may be required to turn Stability 

Assist off. 

ImporTanT:

 You must calibrate  

the receiver each time it is placed  

in bind mode.
To activate AVC, see the steps in  

“Calibrating the Receiver”.

Содержание 1967 Ford Mustang



















Отзывы: