background image

OPERATION AND MAINTENANCE MANUAL 

MAC QM MOTORS 

 

 

 

 

 

 

 

 

 

 

 

PAGE: 49

 

 

 

                  

 

 

CODE: CTT42  EDITION: 01  RELEASE: JULY 2016 

Subject to technical changes without prior notice

 

 

6.2.4

 

Replacement of bearings 

Both the bearings that have been greased for all their service life and those that need to be greased regularly, as well as hermetic 

parts  that  are  subjected  to  wear  and  tear  (seals  and  joints,  etc.),  where  applicable,  must  be  replaced  after  20,000  operating 

hours.  

 
Bearings of the same type as the originals must be installed. Standard bearings for each motor type may be consulted at Table 

18. 

 

The procedure for replacing bearings must be carried out as follows: 

 

1.

 

Disassemble the motor from its location and place it in a safe and clean place. 

 

2.

 

Remove the accessories from the motor very carefully so as not to damage them and then remove the terminal box and 

fan (onlyy in the case that the MAC QM motor has been supplied with tehm). See following sections for more details. 

 

3.

 

Loosen the gland cable outlet. 
 

4.

 

Unscrew the motor seals and covers and remove them. 

 

 

Figure 17: Replacing bearings on MAC-Q motors (step 3 and 4) 

 

 

 

 

 

 

 

 

 

Содержание MAC QM

























































Отзывы: