background image

OPERATION AND MAINTENANCE MANUAL 

MAC QM MOTORS 

 

 

 

 

 

 

 

 

 

 

 

PAGE: 47

 

 

 

                  

 

 

CODE: CTT42  EDITION: 01  RELEASE: JULY 2016 

Subject to technical changes without prior notice

 

 

6.2.1

 

Basic inspection 

 

After assembling the motor or after repairing a breakdown, the motor must be inspected approximately every 500 operating hours 

or at least every six months. 

 
This inspection must consist of basically the following: 

 

With the machine on: 

 

-

 

Check that the motor works according to its rated mechanical and electrical values and that there are no strange 
noises, vibrations or irregular rotation. 

 

With the machine off: 

 

-

 

Check that no cracks appear in the motor fastening elements. 

 

-

 

Check that the connection terminals in the terminal box maintain an adequate fastening. 

 

-

 

If faults are found during the inspection, they must be corrected immediately. 

 

Besides this basic inspection, a number of maintenance tasks must be carried out to ensure that the motor has a long service life. 
The maintenance operations recommended by VASCAT are as follows: 

 

6.2.2

 

Cleaning of the fan and air filter (Only on motors supplied with fan)  

It is important to keep the fan wheel as clean as possible. To do so, apply compressed air to its surface on a regular basis to 

ensure that there are no unwanted particles deposited on it. 

 

The frequency of the cleaning process will depend on the local and environmental conditions that affect the motor, as well as the 

frequency with which the motor is used.  
 

MOVING ROTATING PARTS 

During  the  motor  fan  wheel  cleaning  operation,  the  customer  is  responsible  for  taking  the  necessary  precautions  to  avoid 

accidental contact with the rotating parts. 
 

The fan of the MAC QM motors is fitted with a particle filter of the NGB 290/4 type in the air inlet, which requires regular cleaning. 

The frequency of this operation will depend on the environment in which the motor is located and the frequency with which it is 

used. 
 

To  wash  the  filter,  it  must  be  removed  from  the  fan  and  cleaned  using compressed  air  or  washed  with  water  and  detergent, 

depending on the type of dirt in the environment. The filter must be replaced after 4 or 5 washes by one that is the same as or 

equivalent to the original. 

Содержание MAC QM

























































Отзывы: