background image

 

POWXQG4070

 

EN 

Copyright © 2014 VARO 

P a g e

 | 

3

 

www.varo.com 

GASOLINE CHAINSAW 49.3CC 

18” 

POWXQG4070 

APPLIANCE 

These models  are  intended  for  infrequent  use  by  homeowners, cottagers,  and  campers,  and 
for such general applications as clearing, pruning, cutting firewood, etc. They are not intended 
for prolonged use. If the intended use involves prolonged periods of operation, this may cause 
circulatory problems in the user’s hands due to vibration. 
It is not designed for commercial use. 

WARNING!  Read  this  manual  and  general  safety  instructions  carefully 
before  using  the  appliance,  for  your  own  safety.  Your  power  tool  should 
only be passed on together with these instructions. 

DESCRIPTION (FIG A) 

1. 

Saw chain 

2. 

Guide bar 

3. 

Chain brake lever / hand guard 

4. 

Front handle 

5. 

Starter handle 

6. 

Engine switch 

7. 

Safety trigger 

8. 

Rear handle / boot loop 

9. 

Oil tank cap 

10.  Fuel tank cap 
11.  Guide bar cover 
12.  Bucking spike 
13.  Bar retaining nuts 
14.  Air cleaner cover 
15.  Choke lever 
16.  Throttle/ trigger 
17.  Lock nut 

 

LOW KICKBACK SAW CHAIN helps significantly reduce kickback or the intensity of 
kickback, due to specially designed depth gauges and guard links. 

 

CHAIN BRAKE is a safety feature designed to reduce the possibility of injury due to 
kickback by stopping a moving saw chain in milliseconds. It is activated by the Chain 
Brake lever. 

 

STOP SWITCH immediately stops the engine when tripped. Stop switch must be pushed 
to ON position to start or restart engine. 

 

SAFETY TRIGGER prevents accidental acceleration of the engine. Throttle trigger cannot 
be squeezed unless the safety latch is depressed. 

 

CHAIN BRAKE LEVER / HAND GUARD protects the operator’s left hand in the event it 
slips off the front handle while saw is running. 

 

CHAIN CATCHER reduces the danger of injury in the event saw chain breaks or derails 
during operation. The chain catcher is designed to intercept a whipping chain. 

NOTE: Study your saw and be familiar with its parts. 

WARNING!  Beware  of  kickback.  Hold  chain  saw  firmly  with  both  hands 
when  using.  For  your  own  safety,  please  read  and  follow  the  safety 
precautions  in  this  manual  before  attempting  to  operate  your  chain  saw. 
Improper use can cause serious injury. 

WARNING!  When  using  gas  tools,  basic  safety  precautions,  including  the 
following, should always be followed to reduce the risk of serious personal 
injury and/or damage to the unit. 

PACKAGE CONTENT LIST 

 

Remove all packing materials 

Содержание Powerplus XQ POWXQG4070





















Отзывы: