![background image](http://html1.mh-extra.com/html/varimixer/w80/w80_operation-manual_854832008.webp)
A rattling sound from the closed part of the mixer.
Adjustment of special v-belt
The mixer starts “striking” when kneading dough
Adjustment of special v-belt
which normally causes no problems.
The mixer changes its speed by itself.
Adjustment of special v-belt
The minimum and the maximum speeds are changing.
Adjustment of speed.
The bowl is too tight or too loose.
Adjustment of bowl fixing
The tool hits the sides of the bowl.
Adjustment of bowl centering
...................................................................................................................................
or damaged tool.
The tool hits the bottom of the bowl.
Adjustment of bowl height
...................................................................................................................................
or damaged tool.
List of Errors
Possible Solutions
Prior to a possible repair or adjustment, switch off the mixer by disconnecting the power cable.
Adjustment of special v-belt:
The distance (X) is only indicative as it de-
pends on the tolerance of the special V-belt
.
1. Start by tightening the v-belts (*).
2. Tighten the special V-belt (A) by moving
one or two washers from (V) to (T).
3. Start the mixer and leave it running while
the nut (U) is tightened completely.
4. On the front pulley set the stud (E) on the
varispeed collar (F) must be placed inside the
lower fork (G) and on the rear pulley set out-
side the fork for belt tightener (B), (both must
point backwards).
5. Tolerances in the transmission might cause
the special V-belt (A) to hit the pins (Z) of the
pulley sets when the speed has been adjust-
ed. In such cases the distance (X) must be
reduced. (+ or - 1/8" of 12 1/4")
6. Then follow the section: “Adjustment of
speed”
Adjustment of speed:
1. The stop screws (J) on the speed lever should be adjusted so
that the measurement (H) is 1/8" on the front and the rear pulley,
at low and high speed, respectively. Tighten the counter nuts (K)
when the speed is correctly adjusted.
2. Tolerances in the transmission might cause that the special
V-belt (A) is hitting the pins of the pulley sets (Z) when the speed
has been adjusted. In such cases the distance (X) must be re-
duced, see
“Adjustment of special v-belt”
, and the speed must
be readjusted.
(X) W80 = 12 1/4" +/- 1/8"
(X) W100 = 12 1/4" +/- 1/8"\
(X) W150 = 12 1/4" +/- 1/8".
7
Содержание W80
