10
5
L
IST
OF
ErrOrS
:
p
OSSIBLE
SOLuTION
:
A rattling sound from the closed part of the mixer.
Adjustment of special v-belt
The mixer starts “striking” when kneading dough Adjustment of special v-belt
which normally causes no problems.
The mixer changes its speed by itself.
Adjustment of special v-belt
The minimum and the maximum speeds are changing.
Adjustment of speed.
The bowl is too tight or too loose.
Adjustment of bowl fixing
The tool hits the sides of the bowl.
Adjustment of bowl centering
The tool hits the bottom of the bowl.
Adjustment of bowl height
Prior to a possible repair or adjustment, switch off the mixer by disconnecting the power cable
.
A
djuSTmENT
OF
SpECIAL
v
-
BELT
:
The distance
(X) (Fig. 6)
is only indicative as it depends
on the tolerance of the special V-belt.
1.
Start by tightening the v-belts
(
*
).
2.
Tighten the special V-belt
(A)
by moving one or two
washers from
(V)
to
(T)
.
3.
Start the mixer and leave it running while the nut
(U)
is tightened. Do not tighten it too much.
4.
On the front pulley set the stud
(E)
on the varispeed
collar
(F)
must be placed inside the lower fork
(G)
and
on the rear pulley set outside the fork for belt tightener
(B)
, (both must point backwards).
5.
Tolerances in the transmission might cause that the
special V-belt
(A)
is hitting the pins of the pulley sets
when the speed has been adjusted. In such cases
the distance
(X)
must be reduced.
6.
Then follow the section:
“Adjustment of speed”
A
djuSTmENT
OF
SpEEd
:
1.
The stop screws
(J) (Fig. 6)
on the speed lever
should be adjusted so that the measurement
(H)
is
1-2 mm
on the front and the rear pulley, at low and
high speed, respectively. Tighten the counter nuts
(K)
when the speed is correctly adjusted.
2.
Tolerances in the transmission might cause that the
special V-belt
(A)
is hitting the pins of the pulley sets
(Z)
when the speed has been adjusted In such cases
the distance
(X)
must be reduced, see
“Adjustment
of special v-belt”
, and the speed must be readjusted.
Содержание V30
