Varian 4000 GCMS Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 63

background image

03-914998-55:6

5 of 63

Introduction

This installation procedure represents a stepwise guide to setting up the 4000
GCMS system, meeting product specifications, and carrying out basic customer
familiarization.

The 4000 MS has several modes of operation. It is not desirable to test all of
these modes at installation. The customer needs to decide what will be the
standard mode or preferred mode of operation when the system is sold. The
system will be shipped in the preferred mode. Install and test the system using
the preferred mode. Additional ionization mode demonstrations may be sold. If
so, these ionization modes should also be demonstrated. Under normal
circumstances, the 4000 MS installation should be complete within 2-3 days on
site. Demonstration of additional ionization modes will increase the time needed
to install a system.

A Typical MS Installation

1. System unpacking, setup and checking

2 hours

2. Power up, pump down, initial customer familiarization

4 hours

3. Verification of GC/MS System Operation

2 hours

4. EI ionization mode demo

1 hours

5. Additional customer familiarization

4 hours

Option Installation

1. Autosampler installation, check out, familiarization

1.5 hours

2. CI ionization mode demo, familiarization

1.5 hours

Installation results should be entered into the Installation Tracking Database.

The following should be determined before arriving at an installation site:

The CSR should be aware of whether the customer has met the important site
requirements outlined in the Pre-Installation Document.

A phone call should be

placed with the customer to pre-qualify the site.

The critical site requirements

are bench space and load, power, temperature, humidity, carrier gas purity
(helium) and CI gas purity (external only, methane). The specific requirements
are clearly outlined in the 4000 Pre-Installation Document.

It is also important to determine, before going on site, whether the customer
desires to use the existing system PC or the PC included with the MS upgrade.

If

the customer provides the PC, then the set up of this computer should be a
billable call, and not charged to installation.

In addition, Varian assumes no

liability for configuration or operational problems associated with the customer's
computer.

«
...
3
4
5
6
7
...
»

Содержание 4000 GCMS
































































Отзывы:

Нет отзывов

Похожие инструкции для 4000 GCMS

Бренд: GE Страницы: 242

Бренд: GE Страницы: 24

Бренд: Balanced Body Страницы: 3

Бренд: Ecco Страницы: 9

Бренд: Talet Equipment Страницы: 17

Бренд: Parata Страницы: 40

Бренд: OfiTE Страницы: 21

Бренд: Earthlite Страницы: 4

Бренд: YATEK Страницы: 78

Бренд: Cameo Страницы: 64

Бренд: Cameo Страницы: 100

Бренд: CAME Страницы: 32

Бренд: Warehouse-lighting Страницы: 3

Бренд: E2S Страницы: 5

Бренд: iFIT Страницы: 11

Бренд: R&S Страницы: 2677

Бренд: Tascam Страницы: 3

Бренд: Calibre Fitness Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды