Vari Samson - 56 BK Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 22

Vari Samson - 56 BK Скачать руководство пользователя страница 16

16

Figure 4 :

POWER ASSIST CLUTCH LEVER

Wheel power assist engaged

Wheel power assist disengaged

catch disengaged

catch arrested



In the event of any critical situation release the handlebars immediately. The
safety ignition breaker stops the engine and machine stops.

As a consequence of a small wheel spacing and their small diameter it is possible that
the machine be turned round on a small radius. We are recommending you slightly
decrease engine speed and slightly lift the machine when turning round on the ends of
rows.

If you do not want the blades to be in operation while travelling across an area it is
possible that the machine drive be disengaged from the gear box. It is sufficient in this
case to pull up the arresting pin on the drive flange , push out a little the drive of the
working machine by about 2 cm and slide in again the arresting pin, in this way the
drive of the working machine is ensured.



The disengagement of the working machine drive and disconnecting of the drive
should be carried out at the machine standstill, at the engine stopped and the power
assist clutch engaged!

«
...
14
15
16
17
18
...
»

Содержание Samson - 56 BK























Отзывы:

Нет отзывов