Vari RBS-700D, Руководство по эксплуатации

Страница: 19 / 56

RBS-700D

It is prohibited to work with the machine on any road of any class while the work tool is attached to the machine; the
perpendicular crossing of such roads is permissible in the places where it is specifically allowed.

Always turn OFF the engine and wait for the work tool to stop before performing any work in the close vicinity of the machine!
Before leaving the machine, always turn off the engine and secure it so that it cannot get accidentally turned on.

It is forbidden to remove any protective devices and covers from the machines.

Any repairs, adjustments, lubrication, and cleaning of the machine must be carried out when the machine is at a standstill and
its spark plug connector is disconnected.

When working with lubricants and cleaning the machine, observe the basic hygiene regulations and observe the environmental
protection regulations and laws.
2.2.2 Noise and Vibrations Levels
Description RAPTOR Hydro + RBS-700D
Declared acoustic pressure emission level A at the operator's site 30 ( L
pAd
)
87.0+4.0 [dB]
Declared acoustic output level A 31 (L
WA,d
)
103+4 [dB]
Declared cumulative value of the acceleration of vibrations transmitted to the operator’s hand-
arm 32 a
hv,d
7.2+2.9 [m.s -2 ]
Table 11: Measured Noise and Vibrations Levels
2.2.3 Safety Pictograms
The user is obliged to keep the pictograms on the machine in a legible state and, in case of any damage, ensure their replacement.
The position on the machine is shown in
Fig. 12 on page 51 .
Position: Number: Description:
Sticker on the plastic cover of the working
tool - in the middle
1 Working tool rotation direction arrow – right (clockwise)
Sticker on the plastic cover of the working
tool - on the left
2
3
4
Caution - Before using the device, read through the operating instructions.
Caution - When doing maintenance on the machine, disconnect the spark plug
connector.
It is forbidden to place your hands or feet into the operating area of the cutting
tool – risk of getting cut.
Sticker on the plastic belt cover on the
right in the direction of travel.
5
6 Warning!
Attention, hot surface!
Sticker on the plastic cover of the working
tool - on the right
7
8
9 Minimum safe distance from the machine.
Risk of being hit by flying debris, cuttings, ejected items, etc.
Other persons and animals - keep a safe distance from the machine.
Table 12: Safety Pictograms
2.3 Basic Information
2.3.1 Use of the Machine
Teh brush cutter adaptor RBS-700D is designed for cutting of high thin bladed grass vegetations and wood undergrowth 33 in forests
and on meadows up to maximal height of 80 cm in maintained 34 areas. The areas must not feature any solid items in the growth or rough
terrain. The brush cutter is not designed for park landscaping.

The adaptor is designed only for multifunctional carriers RAPTOR Hydro .

The maximal vegetation height, which can be cut by the brush cutter, is limited by its composition, density and engine
power.

Due to the intended purpose of the brush cutter for the harvesting of high grass vegetations, we do not recommend
cutting vegetations with height below 40 cm. For vegetation with height below 40 cm use the mulcher adaptor
RMS-
600 .

The use for purposes other than the intended purpose is; therefore, to be considered a use for an unspecified
purpose!
30 Measure according to ČSN EN 12733+A1, Annex B and ČSN EN ISO 11201:April 2010
31 Measured according to ČSN EN 12733+A1, Annex B and ČSN EN ISO 3744:2010
32
Measured according to ČSN EN 12733+A1, Annex C, par. C. 4.1.2
33
The brush cutter is not designed to cut any woody growth thicker than 5 mm! A failure to observe this policy will damage the machine.
34
The area growth must be cut and raked at least once a year!
19
re
vi
ze
0
2/
20
18