Vari F-550Z, Перевод оригинальной инструкции

Страница: 22 / 64

F-550, F-550Z, F-550B
Engine Unit F-550 F-550Z F-550B
Model - Honda GCV200 51 Zongshen XP200A 52 B&S 875EXi Series TM 53
Maximum engine RPMs (set) min -1 3200
±
100
Maximum engine incline / short-term 54  20° / 30° 15° / 30° 15° / 30°
Fuel tank capacity l (liter) 0,91 55 1 1 56
Fuel gasoline oct.No. 91-95 57
Engine oil capacity l (liter) 0,4 0,6 0,6
Oil rating SAE / API SAE 30 or 10W-30 / SJ or SH
Table 5: Basic engine information
2.3.2 Description of machine and its components
The F-550 brush cutter frame (on
Pict. 3
) is made of a welded steel frame 11 from formed sheet metal, which all essential machine
components are attached to. The handlebars are mounted to the frame with screw connections 3 and their height may be adjusted into
six positions. All control elements ( 1 , 2 and 4 ) for safe control of the machine are ergonomically distributed along the handlebars.
The handle 12 is used to firmly grasp and direct the machine during operation. A wheel drive clutch lever 2 is located on the left
side of the handlebars, which controls the motion of the machine forward. On the right side is a tool drive clutch lever 1 equipped with
a safety lock to prevent accidental operation 16 , which turns the work tool (blade) drive on or off. If the operator releases the
handles in an emergency, both of the control levers return to the default position and the engine is disengaged from transmitting force. The
blade drive is equipped with an automatic braking device, which stops the blade 58 in the event of an emergency. Motor speed is controlled
by the throttle lever 4 . Motion is secured by wheels 15 with arrows pattern, which are driven by a worm-gear unit. It provides smooth
shifting of force to the wheel via a belt-driven clutch
(the machine moves forward without jerking). The wheel and blade drive transmission
part are covered by plastic housing 9 and 10 . The brake, blade drive clutch, and belt gears in front are also covered from above by a
plastic cover 9 connected by screws to the frame. Pressed on the shaft at the front of the frame is a blade holder with blade 7 . The
blade is fixed and sharp at the ends. The main deck comprises a cover 8 made from hot-dip galvanized (HDG) sheet metal, which except
for the front, spans further than the blade to prevent injury to the operator from flying parts of the mowed area. The deck is riveted from
several parts and screwed to the frame. A plastic shroud is fastened between the wheels. During operation, the machine is guided by a
swivel, height-adjustable spur 5 , which is attached to the front of the machine frame.
2.4 User manual
2.4.1 Assembling the machine

Assembly and operating instructions are available from your retailer as a component of pre-sales service!
Handling points when removing the machine from the box (see Pict. 1 ): ahead of the engine behind the square tube 5 on the engine
plate, at the back of the machine frame tube 4 .
2.4.1.1 Machine assembly procedure
Use the following procedure when assembling: ( We recommend that another person be present to assist you during assembly)
1) According to
Pict. 1
- remove the bag with manuals 2 , spur arm 3 and unfold the paper insert 7 underneath the
handlebars. Hold the machine at the front 5 and back 4 handling points, and remove it from the box.
2) According to Pict. 3 - remove the screw connections 3 from both sides of the frame tube, remove the handlebars, turn them
around and place them on the tube at the rear frame (select one of the three holes in the handlebars to set their height and one
of the two holes in the frame tube). Tighten the screw joints securely by hand. Control lever cables must not be crossed – this
reduces their life!
3) Remove the tie straps from the bag with manuals and attach the control lever cables at the top of the handlebar tube bend.
Only 2 tie straps are required for fastening.
4) According to
Pict. 2
- remove the paper insert ( 6 in
Pict. 1
) from the front of the main deck cover, tilt the machine backwards
onto the handlebars so the rear frame rests on a mat, and secure the machine from tilting back forward. Remove 2 M8 screw
connections ( 1 and 3 ) holding the cover. Hook the tab 2 on the spur arm 5 into the machine frame groove 4 . Lower
the spur arm so that the holes in the spur arm are concentric with the holes in the machine frame. You will feel light cushioning.
Insert the
screws 3 through the holes and attach the nuts 1 . Tighten the screw connection.
2.4.2 Commissioning

The machine may be supplied without engine fluids (depending on various national regulations)!

First, carefully read the engine operating manual 59 ! This will help prevent any engine damage.
51
More information about the engine including replacement part numbers can be found at www.honda-engines-eu.com
52 More information about the engine including replacement part numbers can be found at www.zongshenpower.com
53 More information about the engine including replacement part numbers can be found at www.briggsandstratton.com
54 Short-term = within one minute
55 Measured according to the Society of Automotive Engineer (SAE) standard J1349
56 Measured according to the Society of Automotive Engineer (SAE) standard J1349
57
Vzhledem ke stále se zvyšujícímu podíliu BIOsložkek v palivu používejte stabilizátor paliva.
58
Automatic brake is an active protective element that increases the safety of the machine.
59
Original engine manual and Czech translation is included in the machine packaging.
22
Re
vi
ze
0
1/
20
21