manualshive.com logo in svg

Vanward GD4838S-G, Руководство по сборке, использованию и уходу

Поделиться
Скачать
Vanward GD4838S-G Скачать руководство пользователя страница 23

 

 

 

23 

 

 

Grill Lighting Instructions 

 To  Light the Main Burners 

1 .Make sure the control knobs  are in the “OFF” position.

 

2 .Open the grill hood.

 

3 .Check the ignition pin position and distance between 

the  pin  and  the  burner.  Refer  to  Step 

14

 

of  the 

Assembly Instructions.

 

4 .Make sure the drip  tray is installed. 
5 .Open the LPG  tank.

 

6 .Light each burner separately. Turning on two burner

 

valves together could trip the flow connection (LP grills only).

 

 
 

 
 
 
 
 
 
 

7 .Push  the  control  knob  in  and  turn  the  knob  to  the  left  to  “MAX”  position. 

Keep pressing the knob until the burner is lit.

 

8 .If  the  burner  does  not  ignite  within  5  seconds,  immediately  turn  the 

control knob back to the “OFF” position. Wait 5 minutes and repeat Step 
7 up to 2 or 3 times.

 

9 .If  the  burner  still  does  not  ignite,  TURN  OFF  THE  GAS.  WAIT  5 

MINUTES  for  excess  gas  to  dissipate.  Repeat  Steps  6  and  7(if 
necessary).

 

10 . If the burner still can’t be lit, refer to the Troubleshooting section.

 

 

Replacing the Battery 

1.  Unscrew the electrical ignition button and remove the old battery. 
2.  Replace with a new AA battery 
Note: The negative (-) side of the battery goes in first. Please refer to the mark on the 
side of the cap.   
 

WARNING: 

1. Make sure the hood is completely open each time you attempt to light the 

grill. Failure to open the hood could lead to delayed ignition resulting in 
bodily harm.

 

2. This grill is equipped with a flame observation hole in the side panel. 

Wear protective mitts before using the flame observation hole.

 

 

CAUTION:  It  is  important  to  inspect  the  full  length  of  the  gas  line  hose.  If  it  is 

evident  there  is  excessive  abrasion  or  wear,  or  the  hose  is  cut,  the 
hose must be replaced prior to the appliance being used.

 

 

If required, check your parts list for the proper replacement hose assembly. It will 
be necessary to open the bottom door to fully inspect the hose.

 

 

CAUTION: Regulator and hose must run outside the cart and then route through 

the hole on the left side panel of the cart before connecting with tank. 
See page18 for detailed assembly instructions.

Содержание GD4838S-G





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды