Vantage Hearth VUL24ND Скачать руководство пользователя

Страница: 34 / 36

www.fmiproducts.com

123220-01F

SERVICE HINTS

When Gas Pressure Is Too Low

•  pilot will not stay lit
•  burners will have delayed ignition
•  heater will not produce specified heat
•  propane/LP gas supply may be low

You may feel your gas pressure is too low. If

so, contact your local propane/LP or natural

gas supplier.

ACCESSORIES

FIREPLACE HOOD

Black - GA6050
Antique Brass - GA6053
For all models.

Helps deflect heat away from

mantel or wall above fireplace. Fits openings

28" to 48" wide.

TECHNICAL SERVICE

You may have further questions about

installation, operation, or troubleshooting.
If so, contact FMI PRODUCTS, LLC at

1-866-328-4537. When calling please have
your model and serial numbers of your
heater ready.
You can also visit our web site at

www.fmiproducts.com

REPLACEMENT PARTS

Note: Use only original replacement parts.
This will protect your warranty coverage for
parts replaced under warranty.

Contact authorized dealers of this product.

If they can’t supply original replacement

part(s), call FMI PRODUCTS, LLC at

1-866-328-4537.

When calling, have ready:
•  your name
•  your address
•  model and serial numbers of your heater
•  how heater was malfunctioning
•  purchase date
Usually, we will ask you to return the part to

the factory.

Purchase these accessories from your
local dealer. If they can not supply these

accessories call FMI PRODUCTS, LLC at

1-866-328-4537 for information. You can
also write to the address listed on the back
page of this manual.

DAMPER CLAMP - GA6080

Permanently opens chimney flue damper for

vented operation.

LAVA ROCK - GA6060

For all models.

Order when additional rock

is desired.

f i r e - p a r t s . c o m

Содержание VUL24ND





































Результаты поиска

Содержание VUL24ND

Отзывы:

Похожие инструкции для VUL24ND

Бренды по названию

Популярные бренды

Vantage Hearth VUL24ND, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание VUL24ND

Отзывы:

Похожие инструкции для VUL24ND

Бренды по названию

Популярные бренды