Vantage Hearth VUL24ND Скачать руководство пользователя

Страница: 13 / 36

www.fmiproducts.com

123220-01F

INSTALLATION

Continued

Area of Various Standard Round Flues

Diameter

Area

20 sq. inches

29 sq. inches

39 sq. inches

51 sq. inches

Chimney Height

Minimum Permanent

Flue Opening

6' to 15'

39 sq. inches

15' to 30'

29 sq. inches

Damper

Damper
Clamp

Damper

Damper
Clamp

Damper

Figure 10 - Attaching Damper Clamp

Manufactured Fireplace

Masonry Fireplace

INSTALLING HEATER BASE
ASSEMBLY

WARNING: You must secure

this heater to fireplace floor. If

not, heater will move when you

adjust controls. Moving heater

may cause a gas leak.

WARNING: If installing in a

sunken fireplace, special care

is needed. You must raise the

fireplace floor to allow access

to heater control panel. This

will insure adequate air flow

and guard against sooting and

controls being damaged. Raise

fireplace floor with noncombus

tible material. Make sure material

is secure.

CAUTION: Do not pick up

heater base assembly by burn

ers. This could damage heater.

Only handle base assembly by

grates.

IMPORTANT:

Make sure the heater burners

are level. If heater is not level, heater will not

work properly.

Installation Items Needed

• hardware package (provided with heater)
• approved flexible gas hose and fittings (not

provided) (if allowed by local codes)

• sealant (resistant to propane/LP gas, not

provided)

• electric drill with 3/16” masonry drill bit

Note: Install optional Receiver and Hand-Held
Remote Control Kit (see Accessories, page
34) before installing gas log heater. See instal-
lation instructions included with the kit.

If reasons number 1 or 2 apply to you, you
must permanently open chimney flue damper.

You must install the damper clamp accessory

(to order, see

Accessories

, page 34). This

will insure vented operation (see Figure 10).
The damper clamp will keep damper open.
Installation instructions are included with
clamp accessory.

See chart below for minimum permanent flue

opening you must provide. Attach damper

clamp so the minimum permanent flue open

ing will be maintained at all times.

f i r e - p a r t s . c o m

Содержание VUL24ND





































Результаты поиска

Содержание VUL24ND

Отзывы:

Похожие инструкции для VUL24ND

Бренды по названию

Популярные бренды

Vantage Hearth VUL24ND, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание VUL24ND

Отзывы:

Похожие инструкции для VUL24ND

Бренды по названию

Популярные бренды