10
105604
UNVENTED 32" LogMate
®
FIREBOX
®
For more information, visit www.desatech.com
Figure 18 - Installing Cabinet Mantel
,,,,,
,,,,,
QQQQQ
QQQQQ
¢¢¢¢¢
¢¢¢¢¢
,,,,
,,,,
,,,,
,,,,
,,,,
QQQQ
QQQQ
QQQQ
QQQQ
QQQQ
¢¢¢¢
¢¢¢¢
¢¢¢¢
¢¢¢¢
¢¢¢¢
Cabinet
Mantel
INSTALLATION
Continued
FIREBOX INSTALLATION
USING OPTIONAL
ACCESSORY MANTELS
This firebox may be installed using the cor-
ner or cabinet mantel with hearth base acces-
sories against a wall in your home. You must
use a GA6090 brass trim kit included with
the mantel accessories (see Accessories,
pages 12 and 13). Follow the instructions
below to install the firebox in this manner.
Note:
The instructions below show installa-
tion using GM100F/GM101U/GM102W/
GM106F/GM107U series cabinet mantels
and the G3000F/G3001U/G3004W/G3006F/
G3007U series hearth base accessories. The
hearth base accessory shown is optional for
this installation. You can install firebox and
cabinet mantel directly on the floor. The
corner mantel cannot be installed with the
G3000F/G3001U/G3004W/G3006F/
G3007U series hearth base. You must install
corner and face mantels directly on the floor.
If mounting firebox and cabinet mantel to the
Figure 17 - Placing Hearth Base Accessory
Against Wall
,,,,,
,,,,,
QQQQQ
QQQQQ
¢¢¢¢¢
¢¢¢¢¢
Electrical
Outlet
Hearth
Base
Flexible
Gas Line
Gas Line
Access
Hole
Figure 14 - Cutting Brackets
Figure 13 - Removing Firebox Bottom
Cut to
7 1/4"
Length
Heater Base
Mounting
Bracket
Firebox
Bottom
Screws
INSTALLING FIREPLACE
SCREEN
1.
Insert each rod through nine rings lo-
cated at top of screen.
2.
Insert first rod into rear hole in left side
of firebox. Fasten rod to rear hole near
center of firebox using black shoulder
screw.
3.
Insert other rod into front hole on right
side of firebox and fasten using remain-
ing shoulder screw.
Figure 15 - Installing Fireplace Hood
Hood
Hood
Mounting Slot
Screw
Shoulder
Screw
INSTALLING FIREPLACE
HOOD
1.
Attach three zinc-colored shoulder
screws to back of hood.
2.
Insert hood into hood-mounting slots
on firebox.
3.
Hold hood in place. Insert two black
Phillips screws through bottom of hood
and tighten.
Figure 16 - Installing Fireplace Screen
(Shown Without Fireplace Hood for
Clarity)
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
Rod
Front
Hole
Ring
Screen
Screw
Rear Hole
floor or using corner mantel, an optional
G3005 Slim Base kit may be installed.
1.
Assemble cabinet mantel, hearth base,
brass trim, and trim accessories. As-
sembly instructions are included with
each accessory.
2.
If using an optional GA3700 blower
(FB32CA and NLFB32C models
only), install a properly grounded, 120
volt three-prong electrical outlet at
firebox location if an outlet is not
there. If possible, locate outlet so cabi-
net mantel will cover it when installed
(see Figure 18).
3.
Install gas piping to firebox location.
This installation includes an approved
flexible gas line (if allowed by local
codes) and a manual shutoff valve. The
flexible gas line must be the last item
installed on the gas piping. See Con-
necting to Gas Supply in your log set
owner’s manual.
NOTICE: A qualified service per-
son must connect firebox to gas
supply. Follow all local codes.
