Assembly
Assembly
Assembly
Assembly
Assembly
8
Maintenance
Maintenance
Maintenance
Maintenance
Maintenance
21
1.
Remove the glass stage insert and unplug the main power cable and reflected
illuminator power cable from the rear of the microscope stand. Carefully lay
the microscope onto it’s back.
2.
Open the lamp access compartment located on the bottom of the microsope
base by turning the set knob (figure 57) counter-clockwise until the door
comes loose.
3.
When replacing, insert the new lamp into the lamp socket (figure 58). Make
sure that the pins on the lamp line up with the holes on the lamp socket. The
pins should slide freely into the holes with only slight resistance - do not
force.
4.
Close the compartment door and retighten the set knob. Follow the
instructions in the Transmitted Illumination Setup section to properly center
the lamp.
Replacing the Transmitted Illuminator Lamp
Before attempting to replace or remove the lamp,
UNPLUG THE MICROSCOPE FROM ANY POWER
SOURCE and allow to cool.
!
Be careful not to touch the glass bulb when replacing -
use a tissue or other medium to grasp the lamp. This
will prevent the oils in your hand from reducing lamp
life. If contact is made with the glass bulb, clean with
rubbing alcohol and allow a brief drying period.
!
Replacement Lamp
- 30W 12V Halogen (Cat. No. 1400-30W12VHL)
1.
Open the lamp housing door located at the rear of the reflected illuminator
box by pulling downward (figure 59).
3.
When replacing, insert the new lamp into the lamp socket. Make sure that
the pins on the lamp line up with the holes on the lamp socket. The pins
should slide freely into the holes with only slight resistance - do not force.
4.
Close the compartment door and follow the instructions in the Reflected
Illumination Setup section to properly center the lamp.
Replacing the Reflected Illuminator Lamp
Replacement Lamp
- 50W 12V Halogen (Cat. No. 1400-50W12VHL)
Figure 57
Figure 59
Contact us for current pricing and part numbers
Camera Kits
USB with Image Capture Software
DSLR
CCD Video
Video Eyepiece
Eyepiece Reticles
5mm Scale
10mm Scale
0.500” Scale
10mm Grid
Crosshair
Pointer
Metric & SAE Scale Calibration Plates
Objectives
50X LWD 0.70NA, 3.68mm Working Distance
60X LWD 0.75NA, 3.18mm Working Distance
80X LWD 0.80NA, 1.25mm Working Distance
100X LWD 0.85NA, 0.40mm Working Distance
Miscellaneous
Microscope Optical Cleaning Kit
4”x6” Lens Paper
Optical Tissue
Included Parts
Optional Accessories
Trinocular Head Assembly
1 ea.
Reflected Illuminator Assembly
1 ea.
Reflected Illuminator Lamp Housing
1 ea.
Stand
1 ea.
Brightfield Abbe Condenser
1 ea.
10X High Eyepoint Ultra-Widefield Eyepiece 2 ea.
5X Plan Infinity LWD Objective
1 ea.
10X Plan Infinity LWD Objective
1 ea.
20X Plan Infinity LWD Objective
1 ea.
40X Plan Infinity LWD Objective
1 ea.
Glass Stage Insert
1 ea.
Dispersion Filter
1 ea.
Blue Filter
1 ea.
Spare 30W/12V Halogen Lamp for
Transmitted Illuminator (#1400-30W12VHL) 1 ea.
Spare 50W/12V Halogen Lamp for
Reflected Illuminator (#1400-50W12VHL)
1 ea.
Spare 3A Fuse (#1400-FS5)
1 ea.
Power Cord
1 ea.
Rubber Eyecups
2 ea.
2mm Hex Wrench
1 ea.
3mm Hex Wrench
2 ea.
Operation Manual
1 ea.
Warranty Card
1 ea.
Dust Cover
1 ea.
For information about parts, accessories, or service -- contact your dealer directly
or contact VanGuard Microscopes at 1-800-423-8842.
Figure 58
set knob
lamp socket
lamp
socket
housing
door
For information about parts, accessories, or service -- contact your dealer directly
or contact VanGuard Microscopes at 1-800-423-8842.
