background image

www.vanco1.com

8

IR PASS-THROUGH

IR PASS-THROUGH 

The bi-directional IR system allows you to control the source that is connected to the extender unit, from 
the display; or the display from the source, not simultaneously. There are two important things to note when 
setting up the IR system:

1.  The IR Receiver (IR RX) is always what you point your remote at to send an IR signal. This pigtail is placed 

at the display for controlling the source; or at the source for controlling the display.

2.  The IR Emitter (IR TX) is what sends the IR signal to what you are intending to control, whether it’s the 

source or the display. This pigtail is placed at the source; either pointed at the source, or placed on the 
front panel of the source, see below for placement tips. Or placed at the display to control the display 
from the source.

To Control the Display:

1.  Plug the IR Emitter into the 
IR OUT port of the receiver unit; 
place emitter in front of the IR 
eye of the display

 

2.  Plug IR Receiver into IR IN 
port of transmitter unit; place 
receiver in position where it is 
able to receive remote signals

IR Emitter 

IR RX 

To Control the Source:

1.  Plug the IR Emitter into the 
IR OUT port of the transmitter 
unit; place emitter in front of 
the IR eye of the source

2.  Plug the IR Receiver into IR 
IN port of receiver unit; place 
receiver at or near display

IR RX 

IR Emitter 

Содержание Evolution EVEX4K70













Отзывы: