background image

800.626.6445

7

CONNECTION DIAGRAM

CONNECT AND OPERATE

1. 

Connect a source such as a Blu-Ray Player, game console, A/V Receiver, Cable or Satellite Receiver, etc. 
to the HDMI input on the Transmitting unit

2. 

Connect a display such as an HDTV or HD Projector to the HDMI output on the Receiving unit

3. 

OPTIONAL: Connect a local display to the HDMI loop-out on the Transmitting unit

4. 

Connect a single Cat6 (up to 230ft/70m) to the Cat6 output of the Transmitting unit, and the other end 
to the Cat6 input of the Receiving unit

5. 

OPTIONAL: When using the bi-directional IR control, connect the IR emitter at either end to the IR OUT 
port on either the transmitter or the receiver. When using a powered IR receiver, connect via a 3.5 mm 
stereo plug to the IR IN on either the receiver or the transmitter (See IR section)

6. 

OPTIONAL: Connect an amplifier, soundbar, or audio distribution component to the S/PDIF digital optical 
output on the Receiving unit

7. 

For power, plug in either the Transmitting unit or Receiving unit with the included power supply, opposite 
unit will not have to be plugged in as it features Power over Ethernet (PoE) 

8. 

Power on each device in the same sequence (receiver and transmitter will already be powered when 
either unit is plugged in)

At this point the display connected should display the source signal connected to the extender set. If no 
signal is being displayed, connect a shorter Cat6 cable (jumper or patch cable). If a display is having difficulty 
receiving a signal, access the display’s menu and adjust the resolution (lowest to highest until signal is 
displayed). Use the source remote at the receiver emitter to test IR functionality. If the IR remote function is 
not responding, check the emitters to ensure they are placed correctly and are plugged into the correct IR 
jacks on the Extender set receiving and transmitting units.

NOTE: It is recommended to use a length range within 2~70m network cable. If the cable is too short, there 
may be no display output because the signal is too strong. 

IR Emitter

IR Receiver

IR Emitter

IR Receiver

HDTV

HDMI

HDMI

Source

Содержание Evolution EVEX4K70













Отзывы: