background image

www.vanco1.com

800.626.6445

5

1.  HDMI INPUT: Connect a source such as a Blu-ray player, cable box, computer, NVR/DVR, etc.
2.  IR TX – Plug in included IR Blaster to control the source (see IR section for setup and installation)
3.  IR RX – Plug in included IR Receiver to receive remote signals (see IR section for setup and installation)
4.  Power input – Connect included 12V DC power supply (connect to either Transmitter or Receiver, 

opposite unit will be powered by PoE)

5.  Power Indicator – displays indication that the Transmitter is receiving power, must show solid green
6.  Status Indicator – displays indication that the Transmitter is receiving a signal from the source
7.  RJ45 output – connect a single Cat5e/6 to extend signals, other end to connect to Receiving unit (home-

run cable recommended, any coupling points may result in picture issues, do not use patch panels!)

8.  HDMI OUTPUT – Connect an HDMI display
9.  IR TX – Plug in included IR Blaster to control the display (see IR section for setup and installation)
10. IR RX – Plug in included IR Receiver to receive remote signals (see IR section for setup and installation)
11. Power input – Connect included 12V DC power supply (connect to either Transmitter or Receiver, 

opposite unit will be powered by PoE)

12. Power Indicator – displays indication that the Receiver is receiving power, must show solid green
13. Status Indicator – displays indication that the Receiver is receiving a signal from the Transmitter
14. RJ45 input – connect a single Cat5e/6 to extend signals, other end to connect to Transmitting unit 

(home-run cable recommended, any coupling points may result in picture issues, do not use patch panels!

PANEL DESCRIPTIONS

1

Transmitting Unit 

Receiving Unit 

EDID 

The EV4K2006 is equipped with EDID management, however there is no need to adjust any dip switches or 
dials, the unit automatically reads the EDID from the display and saves it internally.  This feature was created 
for the installer in mind, for a plug and play installation.

2

3

4

5 6

7

8

9

10

11

12 13

14

Содержание Evolution EV4K2006













Отзывы: