Vanco 4x3 HDBaseT Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 20

background image

www.vanco1.com

800-626-6445

13

Configuration: Set HDCP Compliance status for every input, and manage EDID. See the screenshot below:

If there is any modification, press Save to restore the settings, or press Cancel to withdraw.
Interface: Set title bar label and button labels, press Save to save the settings

Network: Inquire and configure network settings including MAC address, IP address, subnet mask, and Gateway

Note: Log in as user access main interface only.

«
...
11
12
13
14
15
...
»

Содержание 4x3 HDBaseT





















Отзывы:

Нет отзывов

Похожие инструкции для 4x3 HDBaseT

GuardSwitch 300 Series

Бренд: GE Страницы: 4

BNI IOL-727-S51-P012

Бренд: Balluff Страницы: 20

Бренд: Erbe Страницы: 118

Бренд: Taiden Страницы: 21

Бренд: Videplus Страницы: 13

Бренд: SICK Страницы: 299

Smatrix Wave Plus Uahome Module R-167

Бренд: Uponor Страницы: 48

CheetaHub Classic-2041

Бренд: Accton Technology Страницы: 7

Бренд: Edimax Страницы: 8

TK-423K - USB/PS/2 KVM Switch

Бренд: TRENDnet Страницы: 14

Бренд: National Instruments Страницы: 23

Бренд: Abtus Страницы: 4

Бренд: PortaOne Страницы: 78

Бренд: Edge-Core Страницы: 15

Бренд: DELTA DORE Страницы: 3

Бренд: AEB Страницы: 10

Бренд: W Box Technologies Страницы: 15

Бренд: Extron electronics Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды