Value Hobby P-51DMustang Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 21

Value Hobby P-51DMustang Скачать руководство пользователя страница 9

www.valuehobby.com/p-51d-mustang-arf.html

9

Step5. Position the servo between two blocks.

Step6. Drill the mounting holes as shown.

Step7. Use four M2*10mm (0.4in) self-tapping
screws to secure the servo to the mounting blocks.

Step8. Secure a servo extension to the servo lead
and thread the extension through the wing.

Step9. Position the servo hatch in the wing. Install
the control horn in the aileron and install a pushrod
connector to the control horn. (Note: the slot for
control horn has been pre-cut.)

Step10. Connect the Z-bend of the aileron servo
pushrod to aileron servo arm. Use four M2*6mm
(0.2in) to secure the servo hatch to the wing.

Step11. Center the aileron and connect the
pushrod wire to the pushrod connector.

Step12. Installing the flap servo follows the same
procedure as the aileron servo.

Step13. Repeat the pervious steps for the
remaining aileron and flaps servo installation.

«
...
7
8
9
10
11
...
»

Содержание P-51DMustang






















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды