Value Hobby P-51DMustang Скачать руководство пользователя страница 2

www.valuehobby.com/p-51d-mustang-arf.html 

 

2

Dear Customer, 

 

Congratulations on your purchase of P-51D Mustang ARF from Value Hobby. We thank you for your generous 
support, and hope you enjoy your new airplane. 
 
At Value Hobby, we hope to offer competitive prices, good performance, and products that you can setup and 
use with ease. That’s why we extensively researched and tested this airplane, and suggested all the products 
necessary for you to setup properly. We understand that you have many choices when purchasing, and we are 
grateful you choose to buy from us.   
 
As vendors, one of the most gratifying things for us is to hear from our customers. We would welcome any 
suggestion to help us improve. Please make us aware of any errors and imperfections in the airplane or the 
instructions, or about the setup that we suggested. We hope you’ll find our setup suggestions to be helpful, and 
enjoy flying your new airplane. Please feel free to contact us at (630) 948-0947 or email us at 

[email protected]

 

 

Disclaimer

 

 

By purchasing and/or building this model, user assumes ALL liability and risk involved with this product. This 
model should be built and flown by an experienced pilot and only flown at AMA sanctioned sites. 
 
Value Hobby guarantees this model to be free of defects in materials and workmanship at the date of purchase. 
This warranty does not cover any parts damaged by use or modifications. In no way shall Value Hobby’s liability 
exceed the original cost of the purchased model. Further, Value Hobby reserves the right to modify this warranty 
without notice. Value Hobby has no control over the final stages of assembly or the material used for the final 
assembly. No liability shall be assumed nor materials used for the final user-assembled product. By the act of 
using the final product the user accepts all resulting liability. Value Hobby, as a R/C product vendor, provides a 
top quality airplane and instructions to complete the model. The quality and flight characteristics of the finished 
model depend greatly on how it is built; we cannot guarantee the performance for the completed model and 
representations are expressed or implied as to the performance of the completed model. If the buyer is not 
prepared to accept the liability associated with the use of this product, the buyer is advised to return this kit 
immediately, in new and unused condition. 

 

Safety in Assembly 

 
During assembly of this aircraft, you will be asked to use sharp knives and hobby adhesives. Please follow all 
safety procedures recommended by the manufacturers of the products you use, and always follow these 
important guidelines: 
 
ALWAYS protect your eyes when working with adhesives, knives, or tools, especially power tools. Safety glasses 
are the best way to protect your eyes. 
 
ALWAYS protect your body, especially your hands and fingers when using adhesives, knives, or tools, especially 
power tools. Do not cut toward exposed skin with hobby knives. Do not place hobby knives on tables or benches 
where they can roll off or be knocked off. 
 
ALWAYS have a first-aid kit handy when working with adhesives, knives, or tools, especially power tools. 
 
ALWAYS keep hobby equipment and supplies out of the reach of children. 

 
 
 
 

Содержание P-51DMustang






















Отзывы: